another tzr125 project

[corf]

after a few months break from restoring bike with doing a rd125 and tzr 125, sold the tzr and keeping the rd125 mk3 as i had one when i was 17 and spent £1000 on her, i just bought this tzr 125 on a G reg 1990, its had a three spoke conversion, new shocker, new wiring loom etc had a complete engine rebuild and sound very good just need get a new exhaust as i dont now what on it i thing rg a exhaust going to look up what it is(if any one know please say so i can sell it on ebay it), going to respray it, apply my decal set that i sell on ebay polish fork and top yoke make look mint, will be take my time with it as going to be winter project.

____________________
custom made decals and reproduction decals, Yamaha tzr125 and the rd125lc mk1/2 complete full set available.

[corf]

finally start to strip it down, spent a couple hours today stripping , found out what the exhaust is off a nsr250 look right the front been modified to fit the tzr, sound nice with it on, will be change to standard, also how many cdi are there for tzr as does not run when plug all wires in, it got 2rk cdi and 2rh wiring loom, did they do 2rh cdi

____________________
custom made decals and reproduction decals, Yamaha tzr125 and the rd125lc mk1/2 complete full set available.

[corf]

complete stripping, gave it a jet wash when they powder coated the frame did it over the original paint, so managed to get most of one side of by with the jet wash,the other side is not budging how do yo remove powder coat, will see how much going to cost get blasted and re powder coated (payed £80 for my rd but i strip the paint off).

____________________
custom made decals and reproduction decals, Yamaha tzr125 and the rd125lc mk1/2 complete full set available.

[CHR15]

[Rob Fzs]

how much you pay for the bike itself ?

i'm after a old 125 stroker to do up
____________________
'00 Aprilia RS50 > '92 Honda CG > '99 Yamaha Fazer > '91 Yamaha RXS > '79 Suzuki X5. Mod 2 Passed 09/06/2011

CHR15 wrote: you know if cows are making milk, does that mean there pregnant?

[woll]

[corf]

[Rob Fzs]

[corf]

update, frame has been painted and just bought a bench polisher, today had a go at the forks still bit left do on them, been busy buy bit for her, still need to get a few bits, also start to draw up the decals for the 1987 block design tzr should have them available in next couple off weeks

____________________
custom made decals and reproduction decals, Yamaha tzr125 and the rd125lc mk1/2 complete full set available.

[andysdad]

hey im in the middle of restoring a tzr 125aswell, its a 4hw i stripped it all down, rebuilt the top end of mines, polished the aluminium frame, new swingarm bushes, painted swinger, new shock, new rear and front pads, new pirelli tyres, modified tailpiece, running 2 rear lights, tail tidy, monster energy stickers with a few extras, double bubble screen, all panels repaired by me, resprayed in ninja green by Boyle Motors, , Custom one of exhaust, decatted expansion chamber, pinned open powervalve, carbon fibre reeds, exhaust port heightened, inlet ported knife edged, new piston and barrel, not much left to do,
fork seals, battery tray and exhaust bracket, and a few other odd bits, any way mate hope u finish this project as im waiting for a update =]
____________________
1992 TZR 125
1999 Impreza WRX

[corf]

frame complete, fork polished and top yoke, will start putting back together, next job bodywork

____________________
custom made decals and reproduction decals, Yamaha tzr125 and the rd125lc mk1/2 complete full set available.

[CHR15]

looks great

nice to see someone looking after one properly
____________________
Turbocharged Bandit S 1200 / project death weapon / GK73A
junglejim: Fuck you aids head. ///// Cornish: my boobs have been spaffed all over
covent.gardens: Well I say fuck you good Sir, for you do not have the right to tell me that.

[Stuster]

This bike looks great already, I am also still in the middle of restoring another TZR. I like the idea of polishing the forks look brill. I might pinch this idea too as the farther in law has a bench polisher. Would mean taking the front end back off but would compliment the bike really well I think. I want a set of TZR 125 Decals if you could send a few pic to my email address.

stuartsmith18@live.co.uk

Looking forward to seeing how this one turns out.
____________________
“Go faster......... until the thrill of speed overcomes the fear of death...

Yamaha TZR125 x 3 Lifan LF125 14-F I am now starting my Honda VFR400 NC30 Project

[zene]

[very nice work!!! how long did it take you to polish it? and what did you use?? i will do the same to mi mito
juan

[corf]

spent couple hours today putting back together, engine, micron exhaust (clips and spring and old flange seem done the trick for fitting), 2 bottle back on etc

____________________
custom made decals and reproduction decals, Yamaha tzr125 and the rd125lc mk1/2 complete full set available.

[2Smoke]

I spent many a mile on a TZR125, excellent little bikes!

Top job on the resto!
____________________
Currently in the stable.. '89 TDR250, 86 NSR250 '79 350LC, '79 DT175MX, 82, Pasola, '98 R1, '95 Speed Triple.. all of them total sheds..

[TZRBOY]

Hi Guys I have a TZR 125 with mega low miles on an F reg. Basically and im no expert but it has crash damage down the right hand side and a cracked casing (Cog sticking out) and bent pegs/gearleaver and needs fairing repaired + new handlebars etc. its mega low miles as i had it for a week back in 93 and spent 2 years recovering from my accident. The crash was at less than 30mph and I unfortunatly took the brunt of the dammage. Reluctantly I now need to sell the bike and wondered what I should expect to advertise it for. Still have all the fairing etc. Any advice welcome. Cheers

[Whosthedaddy]

Wow, that looks well built. I admire the attention to detail for a bike you hardly see anymore.

Well done that mane!
____________________
Current XJ6 S Past ZXR750 H2 : FZR600 : ZX7R P3 : YW100 : TRX850: Trophy 900 T309 : GSXR 600 L0: Monkeybike
Whosthedaddy

[Frost]

awesome little bikes, though i'm not a fan of the exhaust positioning and bodywork. Given any thought's on changing them?

[corf]

[VTRkemshell10...]

any new photo's?
____________________
Past Rides: Sym Jet Euro X, Gilera DNA, Aprillia RS125 (Spains No1 Replica), 1991 Honda NSF, 2006 Honda CG125, 1992 Honda CB400 Super Four, 2000 VFR800 FY-I
Current Rides: 2001 VTR1000 FIRESTORM

[corf]

[corf]

[corf]

update not done a lot due to bad weather we had -12 etc and snow, got my work shop set up with some heat now,

sold my micron (bought for £30 gave it lick of paint(pj1) and polished end can sold for £85.00

bought a standard exhaust been polishing end can and also polished float bowl (could not get it picture right looks good might polish all my carb on my rd)

[size="5"]wanted
has any got middle and bottom faring mount bracket also after a right hand side panel also indicators. [/size]
____________________
custom made decals and reproduction decals, Yamaha tzr125 and the rd125lc mk1/2 complete full set available.

[ORourke]

Good job so far, you'll have a lovely clean bike in the end.