go out and measure your rear wheels!

feef · Energiser Bunny Joined: 11 Feb 2002 Karma :

...pretty please....

I'm looking for a 17" rear wheel for my race bike, and options are thin on the ground.

If your wheel is 175mm from inside side of disk to inside side of sprocket, then it might be a candidate.

Sooo... if any of you can be arsed to do a bit of measuring for me, then I'd very much apreciate it.

tia

a
____________________
Mudskipper wrote: feef, that is such a beautiful post that it gave me a lady tingle Laughing

Windchill calculator - London Bike parking
Blog and stuff - PlentyMoreFish dating

EddyJones · Crazy Courier Joined: 20 Jan 2007 Karma :

Would it not just be R17 on the tyre?

If so Bt090 Smile

garth · World Chat Champion Joined: 15 Dec 2004 Karma :

G · The Voice of Reason Joined: 02 Feb 2002 Karma :

Have you measured SV650 ones?

I presume you don't want 180 width tyre?

Reckon my SM wheels might be quite skinny, that'd be 'different' definitely Smile

.

TUG · World Chat Champion Joined: 12 May 2007 Karma :

You still doing the FZR for race?
Did that guide come to good use i sent you? Why you changing the front now? after a 120 tyre now?
____________________
Haz ER-5, innit!

feef · Energiser Bunny Joined: 11 Feb 2002 Karma :

G · The Voice of Reason Joined: 02 Feb 2002 Karma :

But you do know someone that has several sets of SV wheels Wink

.

Suspect it will be too wide though.
Will try and attach a ruler to one when I get a min, bit busy at the mo.

TUG · World Chat Champion Joined: 12 May 2007 Karma :

Does the 3EN2 have an 18 inch rear wheel? Then i would presume the rules apply, why not just make it easier for yourself and fit a 3TJ rear swinger setup? Or measure the distance between the legs of the swing arm so you know if a wider rim will fit or not?
I misread your OP sorry for the mistake, and the rim size of a 3EN model is 4 x 18(inch) and on the 3tj's its 4.50 x 17(inch) by manuals.
The 3TJ rim uses a 160 width tyre, so measure the distance of your swingarm legs, but on my model (3EN1) it would rub on the swing arm.
____________________
Haz ER-5, innit!

feef · Energiser Bunny Joined: 11 Feb 2002 Karma :

TUG · World Chat Champion Joined: 12 May 2007 Karma :

If your EN2 swinger can take the 3TJ rim then bang it on, you sure it can? is there 170mm width between each swing arm leg? if so just get a 3TJ rim or FZR600 17 inch rim, i think alot of them came in 4.50 aswell.
____________________
Haz ER-5, innit!

hmmmnz · Super Spammer Joined: 22 Aug 2006 Karma :

thats exactly gs500 size, only a 3.5 inch rim though
____________________
the humans are dead
I kick arse for the lord
Wiring Diagrams BIDNIP it bitches

hmmmnz · Super Spammer Joined: 22 Aug 2006 Karma :

actually thats the outside to the outside,
you could get a bandi6 6 wheel with a gs500 sprocket carrier,
____________________
the humans are dead
I kick arse for the lord
Wiring Diagrams BIDNIP it bitches

TUG · World Chat Champion Joined: 12 May 2007 Karma :

Just been on ebay, and looked at a 2TK rim, and 2 FZR 600 rims and asked for sizes for you feef. Let you know when they get back to me and give you the links etc.
____________________
Haz ER-5, innit!

feef · Energiser Bunny Joined: 11 Feb 2002 Karma :

Cheers all...

a
____________________
Mudskipper wrote: feef, that is such a beautiful post that it gave me a lady tingle Laughing

Windchill calculator - London Bike parking
Blog and stuff - PlentyMoreFish dating

kitty kat · World Chat Champion Joined: 20 Jun 2007 Karma :

A Fazer 600 is 200mm, so that is no good to you, but at least I measured it Very Happy

Do I get any Brownie points now? Laughing

____________________
Enjoy everyday, tell those you love everyday you love them
Life is too short to fall out with people

feef · Energiser Bunny Joined: 11 Feb 2002 Karma :

Gazdaman · I did a trackday!!! Joined: 12 Aug 2004 Karma :

Try a TZR250 wheel. Or even a TZR125, or an SZR660 (same wheel). The latter two get snapped up by MZ racers before you'll probably get a look in.

TZR250 takes a 140section standard I think. Mine had a 150 shoehorned in.

Consider an RS125 rear aswell, although they're probably too wide.

Gaz

Azonicben · Could Be A Chat Bot Joined: 22 Aug 2007 Karma :

just nipped out with my tape 175mm centre/centre disc/sprocket on a hyosung gt125r Thumbs Up

____________________
Cbt-23/09/07.....Theory-16/09/08.....Das passed 10/10/08.....
Current bike- GsxR750 K4. Broken: Cbr400rr (Nc29) Sold: Hyosung GT125R

feef · Energiser Bunny Joined: 11 Feb 2002 Karma :

TUG · World Chat Champion Joined: 12 May 2007 Karma :

2TK rim is a 18" and the blokes with the FZR6 rims on ebay one hasnt contacted me yet and the other says he doesnt have one... But its for sale... Confused

Sorry.
Still think that you should find a 3TJ rim from a breakers or a bike being broken.
EDIT:Fox eye rim is 5"
____________________
Haz ER-5, innit!

TUG · World Chat Champion Joined: 12 May 2007 Karma :

Found this...
____________________
Haz ER-5, innit!

feef · Energiser Bunny Joined: 11 Feb 2002 Karma :

TUG · World Chat Champion Joined: 12 May 2007 Karma :

feef · Energiser Bunny Joined: 11 Feb 2002 Karma :

TUG · World Chat Champion Joined: 12 May 2007 Karma :

Thanks

and your so close too! SCORE! why not get the front rim as a spare while your there? You never know.
How come you didnt do the R6 race fairing like madsi did over in OZ? Alot of track based FZR's get this done to them, just a thought but if you already have 3TJ track fairing am sure they will fit with a bit of modification just fine.
____________________
Haz ER-5, innit!