Help & FAQs    Search BCF    Members    Groups    Events Calendar
Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


Chain adjuster snapped on one side

 Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

guile
Spanner Monkey



Joined: 20 Mar 2012
Karma :
PostPosted: 15:32 - 02 Jan 2017    Post subject: Chain adjuster snapped on one side Reply with quote
I was tightening up the bolt on one side and it just snapped due to being immersed in a rust pit. How f'ed am I? Is it safe to continue riding after tightening up the rear axle nut?

[img]https://s28.postimg.org/5fhwtfbz1/IMG_1373.jpg[/img]

How can I get the snapped bolt out and how much is this going to cost me.

Thanks.

edit: I'm too potato to get the image embedded properly - but copy/paste the link works
 Back to top
View user's profile Send private message You must be logged in to rate posts

Nobby the Bastard
Harley Gaydar



Joined: 16 Aug 2013
Karma :
PostPosted: 15:37 - 02 Jan 2017    Post subject: Reply with quote
If you take the splindle out, it looks like the chain adjuster can be removed.

Just buy another one.
____________________
trevor saxe-coburg-gotha:"Remember this simple rule - scooters are for men who like to feel the breeze on their huge, flapping cunt lips."
Sprint ST 1050
 Back to top
View user's profile Send private message You must be logged in to rate posts

bugeye_bob
World Chat Champion



Joined: 05 Sep 2013
Karma :
PostPosted: 15:38 - 02 Jan 2017    Post subject: Re: Chain adjuster snapped on one side Reply with quote
guile wrote:
I was tightening up the bolt on one side and it just snapped due to being immersed in a rust pit. How f'ed am I? Is it safe to continue riding after tightening up the rear axle nut?

[img]https://s28.postimg.org/5fhwtfbz1/IMG_1373.jpg[/img]

How can I get the snapped bolt out and how much is this going to cost me.

Thanks.

edit: I'm too potato to get the image embedded properly - but copy/paste the link works



part numbers if you need them.
https://www.mrcycles.com/oemparts/a/kaw/500b7518f8700223e47987cf/swingarm

ebay lists few 2nd hand but you never know how long they will last
 Back to top
View user's profile Send private message You must be logged in to rate posts

guile
Spanner Monkey



Joined: 20 Mar 2012
Karma :
PostPosted: 15:47 - 02 Jan 2017    Post subject: Reply with quote
Looks like the adjusters will slide out, so will order some new ones.

Most important question - is it safe to ride while I wait the replacements to be delivered?
 Back to top
View user's profile Send private message You must be logged in to rate posts
Beehive Bedlam This post is not being displayed because the poster has bad karma. Unhide this post / all posts.

Rogerborg
nimbA



Joined: 26 Oct 2010
Karma :
PostPosted: 16:00 - 02 Jan 2017    Post subject: Reply with quote
guile wrote:
Most important question - is it safe to ride while I wait the replacements to be delivered?

I would, as long as the axle is done up tight.
____________________
Biking is 1/20th as dangerous as horse riding.
GONE: HN125-8, LF-250B, GPz 305, GPZ 500S, Burgman 400 // RIDING: F650GS (800 twin), Royal Enfield Bullet Electra 500 AVL, Ninja 250R because racebike
 Back to top
View user's profile Send private message You must be logged in to rate posts

Ste
Not Work Safe



Joined: 01 Sep 2002
Karma :
PostPosted: 16:10 - 02 Jan 2017    Post subject: Reply with quote
You're fine riding without the adjusters as long as the wheel is aligned corrected and the axle is tight.

Can't you just replace the bolt that snapped?
 Back to top
View user's profile Send private message You must be logged in to rate posts

guile
Spanner Monkey



Joined: 20 Mar 2012
Karma :
PostPosted: 16:16 - 02 Jan 2017    Post subject: Reply with quote
Cool, will take the chance riding and hope I don't end up deaded.

Ste wrote:
You're fine riding without the adjusters as long as the wheel is aligned corrected and the axle is tight.

Can't you just replace the bolt that snapped?


Havn't taken the adjuster out yet as it's getting dark and I need to ride tomorrow morning but given how tough it was to move the bolt, I would be surprised if it isn't seized into the adjuster. Is there any way around this? Put it in a vice and drill through the bolt, then insert lever to twist it out?
 Back to top
View user's profile Send private message You must be logged in to rate posts

kgm
World Chat Champion



Joined: 04 Jun 2015
Karma :
PostPosted: 19:23 - 03 Jan 2017    Post subject: Reply with quote
You can just buy the adjuster (threaded rod cannot be removed from block) and replace it directly. Once the axle bolt has been removed you can just take off the swing arm end cap as you already have and pull the adjuster block out. Dead simple. It's normally pretty nasty in there and full of water (despite clear drain holes) so it's probably worth taking out both sides once a year just to clean it. A little grease around the adjuster block helps prevent so much corrosion in my experience.
 Back to top
View user's profile Send private message You must be logged in to rate posts

kgm
World Chat Champion



Joined: 04 Jun 2015
Karma :
PostPosted: 19:31 - 03 Jan 2017    Post subject: Reply with quote
See attached picture of my 2010 to see what it looks like without the rust.

Just slung it back on there temporarily so I can move it from the ABBA stand onto different bobbins so I can take the swing arm off so that's why theres a couple of bits missing in the photo for anyone who wonders.
 Back to top
View user's profile Send private message You must be logged in to rate posts

Tdibs
Traffic Copper



Joined: 16 Jan 2015
Karma :
PostPosted: 11:11 - 05 Jan 2017    Post subject: Reply with quote
Remember to wire brush all the shit out of there and liberally coat in some rust inhibitor so you dont find it like that again.
____________________
Previous : 09 Vanvan 125| 02' Sv650s || Current: 1999 Xj600n | 1992 DR650 RSE | 2005 Fazer 1000
 Back to top
View user's profile Send private message You must be logged in to rate posts
Old Thread Alert!

The last post was made 7 years, 109 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT + 1 Hour
Page 1 of 1

 
 You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 
Debug Mode: ON - Server: birks (www) - Page Generation Time: 0.07 Sec - Server Load: 0.46 - MySQL Queries: 17 - Page Size: 70.23 Kb