|
Author |
Message |
nutty_nick |
This post is not being displayed .
|
nutty_nick Derestricted Danger
Joined: 14 Jun 2019 Karma :
|
|
Back to top |
|
You must be logged in to rate posts |
|
|
Easy-X |
This post is not being displayed .
|
Easy-X Super Spammer
Joined: 08 Mar 2019 Karma :
|
Posted: 21:56 - 17 Jun 2019 Post subject: |
|
|
The spare wheel on the back is a nice touch ____________________ Husqvarna Vitpilen 401, Yamaha XSR700, Honda Rebel, Yamaha DT175, Suzuki SV650 (loan) Fazer 600, Keeway Superlight 125, 50cc turd scooter |
|
Back to top |
|
You must be logged in to rate posts |
|
|
nutty_nick |
This post is not being displayed .
|
nutty_nick Derestricted Danger
Joined: 14 Jun 2019 Karma :
|
Posted: 22:03 - 17 Jun 2019 Post subject: |
|
|
yeah, turned out to be a necessity as its only powered on the left hand wheel, and at first the tyres were lasting about 25 miles before being down to the canvas |
|
Back to top |
|
You must be logged in to rate posts |
|
|
nutty_nick |
This post is not being displayed .
|
nutty_nick Derestricted Danger
Joined: 14 Jun 2019 Karma :
|
Posted: 22:09 - 17 Jun 2019 Post subject: |
|
|
this was the result of a ride from Evesham to Worcester.. to a local big bike meet
https://i.postimg.cc/NjrQxDgv/20180412-132824.jpg
have since found better tyres, and found that not hammering the living doodats out of it also helps tyre longevity |
|
Back to top |
|
You must be logged in to rate posts |
|
|
Sister Sledge |
This post is not being displayed .
|
Sister Sledge World Chat Champion
Joined: 17 Aug 2018 Karma :
|
|
Back to top |
|
You must be logged in to rate posts |
|
|
nutty_nick |
This post is not being displayed .
|
nutty_nick Derestricted Danger
Joined: 14 Jun 2019 Karma :
|
Posted: 23:01 - 17 Jun 2019 Post subject: |
|
|
hey !! classed as moped due to width of rear wheels and fact one wheel only braked and driven.
Engine has been fine so far, front of box is opened up to direct air and and there are scoops at the front that are the width of the wheels (form the leading edge of the mudguards)
original engine had a pressed steel fan that only span when the wheel was turning, but amazingly you can wring their necks and they just take it (recently rode one to bristol from dauntsey and back again). biggest journey on this so far in one go was 38 miles on a moped road run and a fair bit of that was flat out, I tried to route the exhaust low and out of the box as quick as i could to prevent heat build up, its a work in progress |
|
Back to top |
|
You must be logged in to rate posts |
|
|
Easy-X |
This post is not being displayed .
|
Easy-X Super Spammer
Joined: 08 Mar 2019 Karma :
|
Posted: 00:08 - 18 Jun 2019 Post subject: |
|
|
One wheel driven?! Eeek! My engineering OCD would kick in ____________________ Husqvarna Vitpilen 401, Yamaha XSR700, Honda Rebel, Yamaha DT175, Suzuki SV650 (loan) Fazer 600, Keeway Superlight 125, 50cc turd scooter |
|
Back to top |
|
You must be logged in to rate posts |
|
|
Avoily |
This post is not being displayed .
|
Avoily L Plate Warrior
Joined: 18 Jun 2019 Karma :
|
|
Back to top |
|
You must be logged in to rate posts |
|
|
Mr Hammers |
This post is not being displayed .
|
Mr Hammers World Chat Champion
Joined: 10 Jul 2008 Karma :
|
|
Back to top |
|
You must be logged in to rate posts |
|
|
nutty_nick |
This post is not being displayed .
|
nutty_nick Derestricted Danger
Joined: 14 Jun 2019 Karma :
|
|
Back to top |
|
You must be logged in to rate posts |
|
|
stinkwheel |
This post is not being displayed .
|
stinkwheel Bovine Proctologist
Joined: 12 Jul 2004 Karma :
|
|
Back to top |
|
You must be logged in to rate posts |
|
|
nutty_nick |
This post is not being displayed .
|
nutty_nick Derestricted Danger
Joined: 14 Jun 2019 Karma :
|
|
Back to top |
|
You must be logged in to rate posts |
|
|
nutty_nick |
This post is not being displayed .
|
nutty_nick Derestricted Danger
Joined: 14 Jun 2019 Karma :
|
|
Back to top |
|
You must be logged in to rate posts |
|
|
Old Thread Alert!
The last post was made 4 years, 309 days ago. Instead of replying here, would creating a new thread be more useful? |
|
|
|