Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


Question about compression

Reply to topic
Bike Chat Forums Index -> New Bikers
View previous topic : View next topic  
Author Message

JoysiBoy
L Plate Warrior



Joined: 29 Feb 2024
Karma :

PostPosted: 10:54 - 29 Feb 2024    Post subject: Question about compression Reply with quote

I read that a Honda CB350 can have compression as high as 170 psi. The compression ratio is 9.5 to 1. If you multiply 9.5 times 14.7 psi standard atmospheric pressure you get just over 139 psi. How could you get a higher than that number reading a compression gauge? Thanks for replies.
 Back to top
View user's profile Send private message You must be logged in to rate posts

jeremyr62
Renault 5 Driver



Joined: 06 Dec 2022
Karma :

PostPosted: 11:13 - 29 Feb 2024    Post subject: Reply with quote

You should try asking ChatGPT for a good answer. It told me the the CR is raised to a power which n, which for a petrol engine is about 1.3.

The constant

n in the formula represents an exponent that accounts for the efficiency and characteristics of the compression process in the engine. This exponent is often referred to as the adiabatic or polytropic exponent and varies depending on the specific heat ratio of the gas being compressed, as well as the efficiency of the compression process itself.

In the context of internal combustion engines, the value of

n typically ranges between 1.2 and 1.4 for gasoline engines. The variation accounts for factors such as heat loss to the cylinder walls during compression and the speed of the compression process (whether it is closer to an isothermal or an adiabatic process).

If the compression process is very efficient and approaches an ideal adiabatic process (no heat transfer with the surroundings),

n would be closer to the adiabatic exponent for air, which is about 1.4.
If there is significant heat loss during compression or the process is slower, making it closer to an isothermal process (temperature remains constant),

n would be closer to 1.0. However, in practice, values below 1.2 are less common for engine compression calculations because the process is generally much faster than an isothermal process and involves some level of adiabatic compression.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

A100man
World Chat Champion



Joined: 19 Aug 2013
Karma :

PostPosted: 11:22 - 29 Feb 2024    Post subject: Reply with quote

jeremyr62 wrote:
You should try asking ChatGPT for a good answer. It told me the the CR is raised to a power which n, which for a petrol engine is about 1.3.

The constant

n in the formula represents an exponent that accounts for the efficiency and characteristics of the compression process in the engine. This exponent is often referred to as the adiabatic or polytropic exponent and varies depending on the specific heat ratio of the gas being compressed, as well as the efficiency of the compression process itself.

In the context of internal combustion engines, the value of

n typically ranges between 1.2 and 1.4 for gasoline engines. The variation accounts for factors such as heat loss to the cylinder walls during compression and the speed of the compression process (whether it is closer to an isothermal or an adiabatic process).

If the compression process is very efficient and approaches an ideal adiabatic process (no heat transfer with the surroundings),

n would be closer to the adiabatic exponent for air, which is about 1.4.
If there is significant heat loss during compression or the process is slower, making it closer to an isothermal process (temperature remains constant),

n would be closer to 1.0. However, in practice, values below 1.2 are less common for engine compression calculations because the process is generally much faster than an isothermal process and involves some level of adiabatic compression.


I think, roughly translated, this means the gas heats up during compression contributing to higher pressure PV = nRT if I recall my o-level physics correctly(which I probably don't) P-ressure V-olume T-emprature n & R some constants I can't remember.
____________________
Now: A100, GT250A, XJ598, FZ750

Then: Fizz, RS200, KL250, XJ550, Laverda Alpina, XJ600, FZS600


Last edited by A100man on 21:03 - 29 Feb 2024; edited 1 time in total
 Back to top
View user's profile Send private message You must be logged in to rate posts

stinkwheel
Bovine Proctologist



Joined: 12 Jul 2004
Karma :

PostPosted: 17:22 - 29 Feb 2024    Post subject: Reply with quote

I can't be bothered thinking about it too much but are you sure it's a direct multiplication and doesn't have a square or even a cube in there because you are dealing with volumes and surface areas?

Also, it's a fuel/air mix charge, not just air so there will be a fair bit of atomised fuel in there along with the air which doesn't compress much due to being a liquid.

Also quoted compression ratios are often little more than a guess based on the crown height and swept volume. To calculate it properly takes a fair bit of fucking about with burettes and a reasonable amount of maths.
____________________
“Rule one: Always stick around for one more drink. That's when things happen. That's when you find out everything you want to know.
I did the 2010 Round Britain Rally on my 350 Bullet. 89 landmarks, 3 months, 9,500 miles.
 Back to top
View user's profile Send private message You must be logged in to rate posts
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> New Bikers All times are GMT + 1 Hour
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: birks (www) - Page Generation Time: 0.08 Sec - Server Load: 0.06 - MySQL Queries: 13 - Page Size: 41.94 Kb