Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


Recommended Chain Tools

Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

DroafNekhyb5
L Plate Warrior



Joined: 29 Oct 2013
Karma :

PostPosted: 09:53 - 29 Oct 2013    Post subject: Recommended Chain Tools Reply with quote

I'm looking to replace my chain and sprockets and I'm just wondering what tools other people use? I've seen a lot of horror stories about one time use Motrax stuff, which is why I'm looking for advice. Very Happy
 Back to top
View user's profile Send private message You must be logged in to rate posts

Hetzer
Super Spammer



Joined: 19 Feb 2007
Karma :

PostPosted: 10:07 - 29 Oct 2013    Post subject: Reply with quote

First you need to know the difference between the types of rivets. You can use The Tool on one type (where you drive a stake into it to 'mushroom' it) and the other you have to peen with a hammer. The peened ones also have to be ground off, though I did manage to drive a peened one out before I bent the tool (Motrax, got a refund).
____________________
"There's the horizon! Ride hard, ride fast and cut down all who stand in your way!"
 Back to top
View user's profile Send private message You must be logged in to rate posts
_Iain_ This post is not being displayed because the poster is banned. Unhide this post / all posts.

map
Mr Calendar



Joined: 14 Jun 2004
Karma :

PostPosted: 10:30 - 29 Oct 2013    Post subject: Reply with quote

_Iain_ wrote:
Given Motrax went bust in Jan 2011 I dont think there's much to worry about Laughing
...then there must be several warehouses full of old stock given the availability over t'net Wink

iirc the name was bought by Oxford or J&S (I know J&S bought the rights to Frank Thomas that was part of the same group/names).
____________________
...and the whirlwind is in the thorn trees, it's hard for thee to kick against the pricks...
Gibbs, what did Duckie look like when he was younger? Very Happy
 Back to top
View user's profile Send private message Send e-mail Visit poster's website You must be logged in to rate posts

nathan k
Spanner Monkey



Joined: 28 Mar 2012
Karma :

PostPosted: 10:47 - 29 Oct 2013    Post subject: Reply with quote

If it's just got a clip over a split link, then use needle nose pliers to get it off.
It's all pretty simple, take the front sprocket off (there will be a split pin somewhere probably) followed by the back wheel.

When you put the back wheel in be careful of the pads, it should slide in smoothly, don't press the brake at any point as you'll struggle to get it in. Might be easier to even take the calliper off depending on the bike.

Don't need any special tools other then a paddock stand, even then a pallet or two will suffice.
 Back to top
View user's profile Send private message You must be logged in to rate posts

DroafNekhyb5
L Plate Warrior



Joined: 29 Oct 2013
Karma :

PostPosted: 08:07 - 30 Oct 2013    Post subject: Reply with quote

Hetzer wrote:
First you need to know the difference between the types of rivets.


It's a DID ZVM-X chain that I'm looking at getting and the supplier only states that the "rivet link is supplied with the chain". I've searched and can't seem to find the type of rivet that DID usually supply.
 Back to top
View user's profile Send private message You must be logged in to rate posts

dodgydog
World Chat Champion



Joined: 10 Sep 2009
Karma :

PostPosted: 08:27 - 30 Oct 2013    Post subject: Re: Recommended Chain Tools Reply with quote

DroafNekhyb5 wrote:
I'm looking to replace my chain and sprockets and I'm just wondering what tools other people use? I've seen a lot of horror stories about one time use Motrax stuff, which is why I'm looking for advice. Very Happy


Don't try to press out the old pin with a chain tool, it's almost certain to bend the press pin in the tool.

Whichever you buy, don't forget to undo the sprocket bolts front and rear BEFORE you start hacking at the chain or taking the wheel off (that way you can still have a rideable bike to go and buy a breaker bar or bit of scaffold pole).

I use an angle grinder to take the end off the rivet first, then try to press the rivet out with the tool, if it isn't playing I just grind through the link.

Most chain tools are ok to peen over the rivet link on the new chain, but a couple of hammers are just as good, (used carefully)
____________________
I know that you believe that you understood what you think I said, but I am not sure you realise that what you heard is not exactly what I meant
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

andys675
World Chat Champion



Joined: 08 Feb 2007
Karma :

PostPosted: 10:25 - 30 Oct 2013    Post subject: Reply with quote

my mate justr bought a new one, from beta, they supply tools to jerry burgess, it was £180..............
____________________
Some people feel the rain, others just get wet.
 Back to top
View user's profile Send private message You must be logged in to rate posts
Vincent This post is not being displayed because the poster is banned. Unhide this post / all posts.

yen_powell
World Chat Champion



Joined: 22 Jun 2008
Karma :

PostPosted: 12:51 - 30 Oct 2013    Post subject: Reply with quote

I use one of these after removing a little of the rivet head with a few touches of an angle grinder. I then use the riveter bits on the new chain. I only fit DID chains, the one in the picture is a 525 x ring type.
https://i19.photobucket.com/albums/b165/yen_powell/chain%20swap/P1040345.jpg
https://i19.photobucket.com/albums/b165/yen_powell/chain%20swap/P1040357.jpg
I use the surrounding links to guide exactly how far to push the press fit side plate on before flaring the rivet heads slightly.
https://i19.photobucket.com/albums/b165/yen_powell/chain%20swap/P1040363.jpg
https://i19.photobucket.com/albums/b165/yen_powell/chain%20swap/P1040368.jpg
____________________
Blackmail is a nasty word........but not as nasty as phlegm!
XT1200Z and a DR350 in bits
 Back to top
View user's profile Send private message You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 114 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: birks (www) - Page Generation Time: 0.09 Sec - Server Load: 0.59 - MySQL Queries: 17 - Page Size: 70.26 Kb