Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


marauder gz 125 07 plate goes click on start up

Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

Mark the Hat
L Plate Warrior



Joined: 07 Jan 2014
Karma :

PostPosted: 17:39 - 07 Jan 2014    Post subject: marauder gz 125 07 plate goes click on start up Reply with quote

OK my marauder GHz 125 on a 07 plate has charged battery, fuel, been standing for about a year but goes click when try to start it up. Am a total novice so please keep it idiot proof
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

wr6133
World Chat Champion



Joined: 31 Dec 2013
Karma :

PostPosted: 18:30 - 07 Jan 2014    Post subject: Re: marauder gz 125 07 plate goes click on start up Reply with quote

Mark the Hat wrote:
OK my marauder GHz 125 on a 07 plate has charged battery, fuel, been standing for about a year but goes click when try to start it up. Am a total novice so please keep it idiot proof


You check the battery is actually holding a charge (with a multimeter)?........ as what you describe sounds like a dead battery
 Back to top
View user's profile Send private message You must be logged in to rate posts

misscrabstick
Crazy Courier



Joined: 05 Jul 2013
Karma :

PostPosted: 18:50 - 07 Jan 2014    Post subject: Reply with quote

What WR said I think. Try getting a jump start off someone with jump leads, GET POLARITY RIGHT!
 Back to top
View user's profile Send private message Send e-mail Visit poster's website You must be logged in to rate posts

Walloper
Super Spammer



Joined: 24 Feb 2005
Karma :

PostPosted: 19:05 - 07 Jan 2014    Post subject: Reply with quote

Disconnect the battery leads, clean all connections, re-connect and try again.
Possibility of the battery being gubbed if it's been stood.

Even though a 'charged' battery indicate 13.5 Volts it may not be able to push the stored energy out.

A battery has to be tested in more than one way.
Open Cell Voltage is the easy one you check by conecting a DC volt meter between the + and - posts and read the voltage.

The difficult but more important test is called a High Rate Discharge Test.
This test the battery efficiency at pushing out amps watts and volts and stuff.
To do that you connect a DC voltmeter as before to read the Open Cell Voltage.
Then you apply a load to the battery and watch the voltage drop. A good battery should be able to hold more than 10 volts for a few seconds.
On a gubbed battery the voltage will dive into the low 3s and 4s after the same time.
It is a bit of a specialist test which is also a bit risky if you don't know what you are up to.

The load can be simply the effect of the starter being held on for the test.

Bike in gear, rear brake held on and push to start.
Only if the bike can start in gear. Most bikes have an safety interlock to prevent this.

The alternative is to take the battery to a garage who can test it. Some Halfords places can do it.
____________________
W-ireless A-rtificial L-ifeform L-imited to O-bservation P-eacekeeping and E-fficient R-epair
 Back to top
View user's profile Send private message You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 315 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.06 Sec - Server Load: 0.37 - MySQL Queries: 14 - Page Size: 40.21 Kb