One off link pipe - South East

[_Iain_]

KTM exhaust is weird.

Need a long single linkpipe made up, or a pair of 90degree bends with exhaust spring hooks on.

Is there anywhere in the SE thats able to sort this?

Want noise, my cans are wanged and I can get a pair deal on some lexteks for a lot less than the cheapest direct fit cans @ £300.
____________________
Please be aware that the above post may be full of complete nonsense.
Riding: '07 KTM Duke II, Baotian BT49QT-20 Driving: '88 Volvo 340

[arry]

Hayward & Scott in Basildon - not cheap, but good quality

Pipecraft - also in Basildon. Never used them, but they get good reviews

Powerspeed, in ashford - made up a system for my mate's engine swapped car and did it well

[arry]

And there's me cutting mates out of the deal....

Just remembered I know a guy in Sidcup that's an alloy welder to within 4 thou, who does a lot of one off fabrication stuff for bikes and cars.

I don't know what he's doing for work at the moment as I've not seen him in a while; he's a mate of a mate so I could ask if Sidcup is any good to you?

[P.addy]

[arry]

I've asked my mate if the fish finger man is doing one offs at moment. Will report back

[Kris]

DEP were based around Medway at one point...
____________________
NSR125RR - ZXR750H1 - ZX9R E1 - GSF600S - GSF600SK3 - VFR400-NC30 - SV1000N - ST1100-R - CBR900RR-R - GSF1200SK5 - GSF600SK1 - VFR1200FA - GSXR1000K2 - ZZR1400 D8F
www.prisonplanet.com

[_Iain_]

Sidcups gravy!

DEP are based in Maidstone, however don't deal with the public when I asked about the CR. They did however knock up a screamer pipe on a turbo Civic for peanuts & sell me some tubing.

I might try and pop down there and see if they can have a look at it. Forgot about that, they're about 20mins away and on the way to Paddys.
____________________
Please be aware that the above post may be full of complete nonsense.
Riding: '07 KTM Duke II, Baotian BT49QT-20 Driving: '88 Volvo 340

[P.addy]

Could make me a one off too so I can have a single can on the trumpet...

[_Iain_]

Trumpet wants a low can like the 2014's arrow!
____________________
Please be aware that the above post may be full of complete nonsense.
Riding: '07 KTM Duke II, Baotian BT49QT-20 Driving: '88 Volvo 340

[P.addy]

[G]

- bikes are for riding, not the mantle piece.

Can't you just scoop the guts of the current cans out?

[_Iain_]

C'mon G.

I've finally got a newish bike however it sounds like a lawnmower & the ends of the cans are smashed in where it's been flipped, as is all the side. It looks shit, it sounds shit.

Conclusion, swap cans.

Dont want to pay £300+ for cans so find cheap option! I can't see anything wrong with that?
____________________
Please be aware that the above post may be full of complete nonsense.
Riding: '07 KTM Duke II, Baotian BT49QT-20 Driving: '88 Volvo 340

[G]

[P.addy]

I've managed to get a PM back on some Danmoto cans, £40, baws.

Reckon you should measure the pipe...see what you can magic up from Lextek, speak with arry's boss man and get it done ASAP.

IoW trip init.

[Fizzer Thou]

John Campbell,who used to run Renegade Exhausts up in West Kingsdown,moved to Lockyer Garage up in Chelsfield village.Makes one-offs for cars and bikes.
____________________
Just talk bikes.What else is there?

Always have a 'Plan B'

[_Iain_]

[Wafer_Thin_Ham]

MHP or Mark Hill Performance. He was based in Stevenage/Baldock, but I'm not sure where he is now.
____________________
My Flickr

[G]

Yea, because being able to give someone else some money to make you an exhaust is a great thing to be proud of .

Mark Hill's a decent bloke that knows his stuff - but suspect may be a bit expensive based on that.

[_Iain_]

[Suntan Sid]

Can you use something like this?

https://exhaustpartsuk.com/images/SDC14994.jpg

Found here:-
https://exhaustpartsuk.com/index.php?main_page=index&cPath=102_1384
____________________
"Everybody needs money, that's why they call it money!"

[arry]

PM incoming Iain

[_Iain_]