Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


Metal polishing and carb cleaning

Reply to topic
Bike Chat Forums Index -> Dear Auntie BCF...
View previous topic : View next topic  
Author Message

gavcarter
Could Be A Chat Bot



Joined: 28 Mar 2009
Karma :

PostPosted: 14:40 - 16 Apr 2014    Post subject: Metal polishing and carb cleaning Reply with quote

Hi again!

Remember the open garage / workshop thread?

Turned out it wasn't a good as an idea as first thought, or at least not as a run from home affair.

Two things where mentioned that I know I can do ( almost immediately) and have done a fir bit of both before.

Metal polishing and carb cleaning / servicing ( fitting carb overhaul kits, replacing seals, jets, needles etc etc )

Would there be much demand for such ( seemingly simple services) do you think?

Most of it would be done by post I would imagine, unless any of you want a ride out to drop off some bits to be polished....

Setup-wise is really easy, as I still do the odd bit of polishing, I have a fair amount of the stuff require, carb cleaning etc I can knock together a small tank with various pumps and aerators to get the thick off and finish by hand, before fitting inspecting the seals etc.

Any thoughts?
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

P.addy
Red Rocket



Joined: 14 Feb 2008
Karma :

PostPosted: 14:49 - 16 Apr 2014    Post subject: Reply with quote

That is still running a business from home though right?

Essentially the same without having a garage out the back.

Are you going to replace my carb when you break anything in there? Again, if you damage the swing arm/yokes etc...
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

CaNsA
Super Spammer



Joined: 02 Jan 2008
Karma :

PostPosted: 14:54 - 16 Apr 2014    Post subject: Reply with quote

Pass the popcorn
 Back to top
View user's profile Send private message You must be logged in to rate posts

gavcarter
Could Be A Chat Bot



Joined: 28 Mar 2009
Karma :

PostPosted: 15:07 - 16 Apr 2014    Post subject: Reply with quote

Paddy. wrote:
That is still running a business from home though right?

Essentially the same without having a garage out the back.

Are you going to replace my carb when you break anything in there? Again, if you damage the swing arm/yokes etc...


Garage is already there, bike lift, benches, vices, lathe, I use them all the time for my own interests.....

Yes I would obviously replace something If I broke it.....

Im just basically gauging interest

Just trying to find something to get me off the pc and out the back where I want to be....

I used to make air rifle parts years ago, was always busy - made a decent bit of spare cash and was happy doing it - then came a change to VCR law - and you are no longer allowed to sell air rifle silencers unless you have RFD status. 2nd hand private sales are ok - just not allowed to make them.
That put a massive hole in my earnings on that score....
The lathe is worse for wear now and needing a new one - it is ok if no great deal off accuracy is needed but the slides are sloppy, while its ok for knocking up spacers, and general hobby type stuff it wont cut it any more on high tolerance parts.

heres a couple of the parts


https://i1072.photobucket.com/albums/w375/gavcarter12/stuff%20made/IMGP1336.jpg
https://i1072.photobucket.com/albums/w375/gavcarter12/stuff%20made/DSC00528.jpg
https://i1072.photobucket.com/albums/w375/gavcarter12/stuff%20made/IMGP1337.jpg
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

P.addy
Red Rocket



Joined: 14 Feb 2008
Karma :

PostPosted: 15:26 - 16 Apr 2014    Post subject: Reply with quote

Are you charging for this service and operating out of the house. I don't usually accept any payment for things that I would do to someones bike... just because earning money isn't top game for me. If you really want to start doing this, perhaps setting yourself up as a little company that does this stuff rather than "a guy in a house" and advertise properly, you might earn some.

Personally, think its a non starter, but I'm not an optimist. At all Laughing
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

gavcarter
Could Be A Chat Bot



Joined: 28 Mar 2009
Karma :

PostPosted: 15:40 - 16 Apr 2014    Post subject: Reply with quote

Paddy. wrote:
Are you charging for this service and operating out of the house. I don't usually accept any payment for things that I would do to someones bike... just because earning money isn't top game for me. If you really want to start doing this, perhaps setting yourself up as a little company that does this stuff rather than "a guy in a house" and advertise properly, you might earn some.

Personally, think its a non starter, but I'm not an optimist. At all Laughing


Yes I was planning charging but not a lot...
Small parts Id probably do for the cost of P+P as favor - but I couldn't sweat away spending 4-5 hours polishing a set of fork legs for free....
Couldn't afford to in all honesty

I used to make and sell about 5 silencers a week, £30-50 depending on design
A set of end caps a week £12 - sometimes id make up ten sets in one go and sell them to a gun shop in wales for about £60

Then there was all the one -off's replicating parts in brass or aluminum so they could be polished and look and shiny instead of boring matt black...

So yes Some guy in a house can do quite well - if there is an interest....which brings us back to the original question...

Is there an interest in these areas? Has polished parts gone out of fashion?

I remember when andonized parts where "in" then all of a sudden it was a race to get them off before ya mates took the piss haha
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Whosthedaddy
Super Spammer



Joined: 11 Dec 2005
Karma :

PostPosted: 17:21 - 16 Apr 2014    Post subject: Reply with quote

If you'll be overhauling and upgrading carbs, would you not want it tested like in a rolling road to set it up correctly?
____________________
Current : MSX 125 Past : CBR 900RR Monkeybike : c50 LAC : ZXR750 H2 : FZR600 : ZX7R P3 : YW100 : TRX850: Trophy 900 T309 : GSXR 600 L0: Monkeybike : XJ6S Whosthedaddy
 Back to top
View user's profile Send private message You must be logged in to rate posts

gavcarter
Could Be A Chat Bot



Joined: 28 Mar 2009
Karma :

PostPosted: 17:57 - 16 Apr 2014    Post subject: Reply with quote

Whosthedaddy wrote:
If you'll be overhauling and upgrading carbs, would you not want it tested like in a rolling road to set it up correctly?


Wasn't really looking at the upgrading - cant do that without the rest of the bike really.

Just the general cleaning up, un-gumming jets, floats etc. New seal kits if needed - lots of people are more than happy to twiddle all the screws - half the time when they don't know what they do but a lot of people are scared of opening a carb to clean it....
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Kai.Wilson
Spanner Monkey



Joined: 26 Sep 2009
Karma :

PostPosted: 02:40 - 17 Apr 2014    Post subject: Reply with quote

If someone is scared if cleaning the inside of a carb prob scared of taking it off...
 Back to top
View user's profile Send private message You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 217 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> Dear Auntie BCF... All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.06 Sec - Server Load: 0.47 - MySQL Queries: 13 - Page Size: 63.39 Kb