Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


Sluggish gt125

Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

Dave M
Scooby Slapper



Joined: 03 May 2013
Karma :

PostPosted: 00:09 - 21 Apr 2014    Post subject: Sluggish gt125 Reply with quote

Hysong gt125 new carbs fitted but very slow to pick up revs after gear change.

Tank has been cleaned.
Carbs spotless.
New fuel filter.
Plugs ok.
Garage set up carbs.

Could anyone suggest where I could look next. Takes a long time to warm this bike up with choke. As soon as I twist throttle after all gear changes it stutters then kicks in and sometimes stutters dropping down into 2nd and 1st gear. Hope this makes sense. Cheers.
 Back to top
View user's profile Send private message You must be logged in to rate posts

sickpup
Old Timer



Joined: 21 Apr 2004
Karma :

PostPosted: 01:21 - 21 Apr 2014    Post subject: Reply with quote

Pilot air screws are incorrectly set up. Use a CO2 tester and set to 3-3.5% CO2 at idle, should be about right.
 Back to top
View user's profile Send private message You must be logged in to rate posts

Dave M
Scooby Slapper



Joined: 03 May 2013
Karma :

PostPosted: 10:17 - 21 Apr 2014    Post subject: Reply with quote

sickpup wrote:
Pilot air screws are incorrectly set up. Use a CO2 tester and set to 3-3.5% CO2 at idle, should be about right.


Thank you I will give this a go!
 Back to top
View user's profile Send private message You must be logged in to rate posts

Dave M
Scooby Slapper



Joined: 03 May 2013
Karma :

PostPosted: 11:13 - 21 Apr 2014    Post subject: Reply with quote

Seem to have a flat spot in and around 4k rev range. Could this be more of an electrical problem as someone suggested to me. One of cylinders maybe dropping out? Could it be something like this? What reading do I need when checking the coils?
 Back to top
View user's profile Send private message You must be logged in to rate posts

Dave M
Scooby Slapper



Joined: 03 May 2013
Karma :

PostPosted: 11:20 - 21 Apr 2014    Post subject: Reply with quote

It's also a bugger to start.[/url]
 Back to top
View user's profile Send private message You must be logged in to rate posts

moonzoomer
World Chat Champion



Joined: 01 Jul 2012
Karma :

PostPosted: 21:41 - 21 Apr 2014    Post subject: Reply with quote

Check valve clearances are not too tight ( especially exhaust ), I have found the valve clearances tighten on this model rather than slacken over time so back the clearances of a tad then try to start the bike.
 Back to top
View user's profile Send private message You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 213 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.04 Sec - Server Load: 0.5 - MySQL Queries: 13 - Page Size: 45.19 Kb