|
|
| Author |
Message |
| winz |
This post is not being displayed .
|
 winz World Chat Champion

Joined: 05 Feb 2015 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Pete. |
This post is not being displayed .
|
 Pete. Super Spammer

Joined: 22 Aug 2006 Karma :     
|
 Posted: 12:53 - 09 Aug 2015 Post subject: |
 |
|
Could be not enough free-play, could be the cable is gummed up.
First check your lever free-play because if you have none the clutch will slip.
Release the cable at the engine end. Once it's free you should find you can flap the lever by pushing and pulling the free end of the cable with just finger-tip pressure. If you can't, clean the crud out of the cable or replace it. ____________________ a.k.a 'Geri'
132.9mph off and walked away. Gear is good, gear is good, gear is very very good  |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| RhynoCZ |
This post is not being displayed .
|
 RhynoCZ Super Spammer

Joined: 09 Mar 2012 Karma :     
|
 Posted: 13:14 - 09 Aug 2015 Post subject: |
 |
|
Ride at about 40mph, put it in the top gear (6th, I guess), twist the throttle. If it slips, the clutch is to be replaced or to be adjusted (in your case). If it doesn't slip and the engine starts shaking and having a tendency to die, the clutch is alright and you are being paranoid.
A clutch slippage would be more dramatic than just, the bike is not going any faster. ____________________ '87 Honda XBR 500, '96 Kawasaki ZX7R P1, '90 Honda CB-1, '88 Kawasaki GPz550, MZ 150 ETZ
'95 Mercedes-Benz w202 C200 CGI, '98 Mercedes-Benz w210 E200 Kompressor |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| winz |
This post is not being displayed .
|
 winz World Chat Champion

Joined: 05 Feb 2015 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| RhynoCZ |
This post is not being displayed .
|
 RhynoCZ Super Spammer

Joined: 09 Mar 2012 Karma :     
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| winz |
This post is not being displayed .
|
 winz World Chat Champion

Joined: 05 Feb 2015 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Pol Anorl |
This post is not being displayed because the poster is banned. Unhide this post / all posts.
|
 Pol Anorl Banned

Joined: 13 Apr 2010 Karma :     
|
 Posted: 01:05 - 10 Aug 2015 Post subject: |
 |
|
what type of adjusters do you have? do you have the 10mm nut and posi drive on the sprockt cover? if so try turning the sprocket screw out 1/4 of a turn and see how it goes. ____________________ GOOD GAME BODYGUARD: https://i.imgur.com/8WePGgf.jpg
20:30:37 Pyro.: I don't sort of like men, I take every advantage to choke on dick.
Jewlio Iglesias: You live in Liverpool - Chances are, the front door has already been kicked off the hinges |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
Old Thread Alert!
The last post was made 11 years, 33 days ago. Instead of replying here, would creating a new thread be more useful? |
 |
|
|