mt10 rear brake

[dave001]

had a weird one to day aint been out on bike for a few weeks while ice was about

decided to have a ride to day been riding about a hour and a bit stoped at lights and l had a compleat loss of rear brake presure

no loss of fluid get up the road somewher i can pull in give 3 pumps and have a look got a slite drag what want ther before so it will need looking

but cant get to repeat drag will just caliper be shited up


but tottal of loss of pressure is werid

pinhole sucking air maybe or stuck mater cylinder pistion that freed its self

any ideas?

the slite drag has seemed to prity my freed itself just hopingg it heat disk to much

[Easy-X]

There's not really much to brakes, small piston pumps fluid to another piston. Assuming you don't have some linkage problem (should be pretty obvious) then either the master cylinder is pumping fluid but it's going elsewhere, maybe a leak or a ballooning brake pipe, or it's not pumping fluid in which case it needs a rebuild or replacement.
____________________
Husqvarna Vitpilen 401, Yamaha XSR700, Honda Rebel, Yamaha DT175, Suzuki SV650 (loan) Fazer 600, Keeway Superlight 125, 50cc turd scooter

[dave001]

[Easy-X]

Intermittent problem... maybe some grit in the system?
____________________
Husqvarna Vitpilen 401, Yamaha XSR700, Honda Rebel, Yamaha DT175, Suzuki SV650 (loan) Fazer 600, Keeway Superlight 125, 50cc turd scooter

[dave001]

[Copycat73]

remove the cover of the fluid reservoir .. whilst lookin at the fluid surface .. fully depress the back brake ... see if any back pressure ..
____________________
Whatever I post I have no citation and no intention of providing one..
caveat emptor

[Fizzer Thou]

Seeing as the MT10 has ABS I would suppose that any drag has caused the brake fluid to overheat and cause fade.Once cooled down and pressure has resumed,this is a typical example.

If the fluid has never been replaced it would be best to bleed the system through with fresh fluid from an unopened bottle.Bleed the front calipers as well.One 500ml bottle of DoT4 will be enough to do the job and can be bought from the likes of £5.
____________________
Just talk bikes.What else is there?

Always have a 'Plan B'

[dave001]

[mtriderrob]

If you do change the brake fluid by bleeding it through, you will probably need to activate your ABS once done and then bleed again otherwise you will still have old fluid in the ABS pump which will just contaminate your new fluid again.
There are 2 ways of activating the ABS on the super ten, one method is to use a jumper wire across a couple of terminals on a plug under the seat followed by operating first the front brake and then the rear with the ignition turned on.That’s the recommended Yamaha procedure for my 1200 Super Teneré so I wouldn’t have thought the MT10 would be much different.
The 2nd more fun way to do it is by riding on a loose/slippery surface and trying to lock the wheels, please only use this method if your riding skills allow you to do so, easy to do on a Super Ten, probably less so on an MT10!
____________________
Current bikes; MT01, XTZ1200 & 1981 XV750 which I've had from new, TRS300RR
Scorpa factory 300-still mine despite the fact that some thieving scumbag bastard currently has possession of it

[dave001]

[Nobby the Bastard]

Any chance you two can find a language you both understand rather than the pair of you struggling with English when it's clearly not your first language?
____________________
trevor saxe-coburg-gotha:"Remember this simple rule - scooters are for men who like to feel the breeze on their huge, flapping cunt lips."
Triumph Sprint ST 1050

[dave001]