rc servo again...

[JimboJ]

my part should arrive soon(before 4:00pm) and the rc switch needs replacing. probviding that its fixed the problem the mechanic said i need to re-tune the rc servo motor to open and close properly. HOW THE FUCK do i do that(pardon my french)??
____________________
[00:42] <NSR-Andy> which one's the missionary position
[00:42] <NSR-Andy> i've heard it's good
[9:42pm] <Shaun> you came first mike | <Shaun> yes gav, because I really want to fuck you

[Ropehead]

when u plug the servo in and turn the key the servo should go in to the CLOSED position (closing the power valve) then u conect it up.
make sure the power valve is in the closed position when the servo is.

just make sure it opens the valve Fully after 7500rpm and below that it closes it to the correct position,

Its probably easyer to get the valve FUlly open ajust the servo
(bike turned off) to OPen then fit it, then u knot its defnatly fully operning the powervalve, givving u ALL the top end power

in not 2 sure how they work on the NSR but its x10 easyer if u can see the valve position by removing the blanking plate on the opersit side,

Hope this makes sence

[retrofly]

hi
see jimbo this post actually has relevance, i think i need a new RC-servo or summin, then again it might be an alternator or summin i cant remember, what do u need if all your electrics are buggered up and u starter motor isnt working either?

Luke
____________________
"The food was not undelicious"
-Homer Simpson (Exceptional beast : Underachiving Human)
www.geocities.com/retrofly

[Demonic69]

[Phoenix]

A new battery?

[craigT19]

jim.......

before putting questions like that atleast...go and ask a garrage first

cos i personally have no clue what your talking about??


all the RC servo is...is a SERVO?? basically a motor that turns two cabels..which opens a semi circle plate over the exhaust port....

what is there to program???
____________________
Bikes owned :- 2001 nsr125, 1999 zx6r, 2006 yzf-r1, 2009 xmax 250, 2012 yzf-r1, 2015 MT-07
Current bike : - 2016 MT-10
BCF member pops. sadly missed 1945-2003

[retrofly]

hi
retrofly shoots dem hahahaha

Luke
____________________
"The food was not undelicious"
-Homer Simpson (Exceptional beast : Underachiving Human)
www.geocities.com/retrofly

[JimboJ]

craig knows less than me.........ive been to a garage and he explained it all technically and since he ripped me off(or tried to) i dont intend to go back their and the only other place is RIOSSI
____________________
[00:42] <NSR-Andy> which one's the missionary position
[00:42] <NSR-Andy> i've heard it's good
[9:42pm] <Shaun> you came first mike | <Shaun> yes gav, because I really want to fuck you

[JimboJ]

program?? i didnt say program anywhere did i? i said re-tune i meant re-adjust so that it opens when it should and close when it should. currently it is out of sync
____________________
[00:42] <NSR-Andy> which one's the missionary position
[00:42] <NSR-Andy> i've heard it's good
[9:42pm] <Shaun> you came first mike | <Shaun> yes gav, because I really want to fuck you

[Hunter]

With the stock servo motor/controller, all you can adjust is how fully opened/closed the RC valve works. You cannot vary the RPM range that it opens and closes, not with my controller/cdi anyway!

Its always best to adjust the valve timing when at the fully open position, this will avoid the servo motor getting damaged and will ensure the vlave opens completely.

Get a service manual for your bike, the valve adjustment should be the same as the older versions. I have seen many manuals about!

[craigT19]