Help & FAQs    Search BCF    Members    Groups    Events Calendar
Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


NC35 start ok but cuts out when engages gear!!!

 Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

my996
L Plate Warrior



Joined: 04 May 2008
Karma :
PostPosted: 22:21 - 04 May 2008    Post subject: NC35 start ok but cuts out when engages gear!!! Reply with quote
Hi all...

Hope you can help me on this. Have just got hold of an NC35 to use for trackdays. It starts fine but when you engage a gear, it cuts out. I am assuming it is the sidestand cutout, except there isn't a stand on it (taken off by previous owner).

Anyone know enough about these bikes as to where the wiring would go, so I can trace it back???

Thanks in advance for any help.
Les
 Back to top
View user's profile Send private message You must be logged in to rate posts

damz
World Chat Champion



Joined: 15 Jul 2007
Karma :
PostPosted: 01:43 - 05 May 2008    Post subject: Reply with quote
it doesnt have a stand? Shocked
____________________
Current Bikes RVF400 - 94
Cars: RX7 FD, Eunos Roadster
Former Bikes: FZR 250R 89, ZX7R 98
 Back to top
View user's profile Send private message You must be logged in to rate posts

Rit
Trackday Trickster



Joined: 24 Jan 2006
Karma :
PostPosted: 02:14 - 05 May 2008    Post subject: Reply with quote
Does it jump forward when you engage gear? could be clutch adjustment.
____________________
You watching this rubbish?
Naaaa, switch over, Neighbours is on in a minute!
www.ritzbitz.co.uk
 Back to top
View user's profile Send private message Send e-mail Visit poster's website You must be logged in to rate posts

dr_adams
Borekit Bruiser



Joined: 04 Feb 2004
Karma :
PostPosted: 04:37 - 05 May 2008    Post subject: Reply with quote
no stand as trackbike i assume... does it stall even with clutch in? The wiring is normally where the stand would be, depends on how far it has been taken back but normally a push switch where the side stand would be....
 Back to top
View user's profile Send private message You must be logged in to rate posts

my996
L Plate Warrior



Joined: 04 May 2008
Karma :
PostPosted: 08:59 - 05 May 2008    Post subject: Reply with quote
dr_adams wrote:
no stand as trackbike i assume... does it stall even with clutch in? The wiring is normally where the stand would be, depends on how far it has been taken back but normally a push switch where the side stand would be....


Correct, its a trackbike, and yes before clutch is released. Have looked for the wire at stand end but cannot find anything. Must have been cut back but not a clue how far Sad

Any suggestions (I don't think previous owner will know)...

Thanks again!!!
 Back to top
View user's profile Send private message You must be logged in to rate posts

dr_adams
Borekit Bruiser



Joined: 04 Feb 2004
Karma :
PostPosted: 04:32 - 06 May 2008    Post subject: Reply with quote
i have looked everywhere for a manual to find the wiring diagram but alas i can't find it.... i would prob suggest www.400greybike.co.uk as they would be able to answer instantly, the parts manual shows a two wire connection just behind the stand :S so might be worth having a look for this as its got to be connected or you wouldn't be having the problems! sometimes racers hide them under seats as a cut out:S
 Back to top
View user's profile Send private message You must be logged in to rate posts

dr_adams
Borekit Bruiser



Joined: 04 Feb 2004
Karma :
PostPosted: 04:34 - 06 May 2008    Post subject: Reply with quote
https://www.motoinfo.yoyo.pl/Honda/Honda%20RVF400R.jpg

go there and all is sorted, not brill quality but in the very bottom left is the thing your looking for and you can see where it connects and take it from there:)
 Back to top
View user's profile Send private message You must be logged in to rate posts

my996
L Plate Warrior



Joined: 04 May 2008
Karma :
PostPosted: 07:09 - 06 May 2008    Post subject: Reply with quote
many thanks, will have a go dr_a...
 Back to top
View user's profile Send private message You must be logged in to rate posts

my996
L Plate Warrior



Joined: 04 May 2008
Karma :
PostPosted: 15:25 - 10 May 2008    Post subject: Reply with quote
ok, have found the wires in the loom. There are 3 (yellow/black green/white green) which ones do I connect together???

Again thanks in advance...
 Back to top
View user's profile Send private message You must be logged in to rate posts

my996
L Plate Warrior



Joined: 04 May 2008
Karma :
PostPosted: 18:20 - 11 May 2008    Post subject: Reply with quote
Hi there...

Have figured it out, connect the green with the green/ white trace... job done Smile
 Back to top
View user's profile Send private message You must be logged in to rate posts

binge
Emo Kiddy



Joined: 02 Jul 2004
Karma :
PostPosted: 21:38 - 12 May 2008    Post subject: Reply with quote
Short out the two outside wires. Thumbs Up
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
Old Thread Alert!

The last post was made 17 years, 123 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
 You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 
Debug Mode: ON - Server: birks (www) - Page Generation Time: 0.11 Sec - Server Load: 1.69 - MySQL Queries: 14 - Page Size: 65.13 Kb