 |
|
 |
|
|
| Author |
Message |
| MickC |
This post is not being displayed .
|
MickC
Spanner Monkey
Joined: 27 May 2011
Karma :  
|
 Posted: 12:27 - 28 Aug 2011  Post subject: Stuck Barrels |
 |
|
In the process of stripping my top end. Heads off but the barrels are stuck. Its a 1979 cb900, I've had to hacksaw the bolt at the bottom of the barrels (head was rounded off) and no amount of persuasion is getting them to break their seal. Any suggestions no matter how brutal will be welcome. The barrels are scrap ( I have a brand new set and pistons to go on so damage to the old ones doesn't matter - already tried a lump hammer )
____________________
XX XXXx
Previous: CG125,XS250 (converted to 400),Z250A, GPZ550, Norton Commando, XS500, 78 Laverda Jota, GPZ1100,Harris bonneville, XV750 (mono shock),TR1 |
|
| Back to top |
   |
You must be logged in to rate posts |
|
 |
| unitynotsocri... |
This post is not being displayed because the poster is banned. Unhide this post / all posts.
|
unitynotsocri...
Banned
Joined: 29 Jun 2011
Karma : 
|
Posted: 13:04 - 28 Aug 2011  Post subject: |
|
|
Angle grinder?If thats not possible then drill through the old bolt and scarpe it out.
____________________
nearly a normal tax paying tosser.......with ferrileness suzi100,cg125,cb125scb100n,cb175,cd100,cj250t,kh250,c15,125 bantam,super 6,rickman gs750,xt500,250rs,dt175,lifan125,dolomite1850,metro,Morris220ld,morrisfg,leyland princess,range rover,corsa,vw camper .now struggling with legs. MORE ORDER = MORE CHAOS |
|
| Back to top |
| |
You must be logged in to rate posts |
|
|
| MickC |
This post is not being displayed .
|
MickC
Spanner Monkey
Joined: 27 May 2011
Karma :
|
| Posted: 13:34 - 28 Aug 2011 Post subject: |
|
|
Nice one, just cut round where the bolt was and off they came.
____________________
XX XXXx
Previous: CG125,XS250 (converted to 400),Z250A, GPZ550, Norton Commando, XS500, 78 Laverda Jota, GPZ1100,Harris bonneville, XV750 (mono shock),TR1 |
|
| Back to top |
| |
You must be logged in to rate posts |
|
|
| unitynotsocri... |
This post is not being displayed because the poster is banned. Unhide this post / all posts.
|
unitynotsocri...
Banned
Joined: 29 Jun 2011
Karma :
|
| Posted: 13:59 - 28 Aug 2011 Post subject: |
|
|
whne putting the barrels back on make sure the rings are all lined up correctly(three rings per piston ,ring gap usually 120 degree apart) and oil the piston tops/rings before lowering the barrels,good luck.
____________________
nearly a normal tax paying tosser.......with ferrileness suzi100,cg125,cb125scb100n,cb175,cd100,cj250t,kh250,c15,125 bantam,super 6,rickman gs750,xt500,250rs,dt175,lifan125,dolomite1850,metro,Morris220ld,morrisfg,leyland princess,range rover,corsa,vw camper .now struggling with legs. MORE ORDER = MORE CHAOS |
|
| Back to top |
| |
You must be logged in to rate posts |
|
|
| stinkwheel |
This post is not being displayed .
|
stinkwheel
Bovine Proctologist
Joined: 12 Jul 2004
Karma :
|
|
| Back to top |
| |
You must be logged in to rate posts |
|
 |
Old Thread Alert!
The last post was made 14 years, 115 days ago. Instead of replying here, would creating a new thread be more useful? |
 |
|
|
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum
|
Read the Terms of Use! - Powered by phpBB © phpBB Group
Debug Mode: ON - Server: birks (www) - Page Generation Time: 0.06 Sec - Server Load: 0.84 - MySQL Queries: 14 - Page Size: 44.9 Kb
|
Help & FAQs
Search BCF
Members
Groups
Events Calendar
rating
rating