|
|
| Author |
Message |
| Pigeon |
This post is not being displayed .
|
 Pigeon World Chat Champion

Joined: 27 Sep 2012 Karma :    
|
 Posted: 20:07 - 01 Mar 2014 Post subject: Indicators not doing much but indicating something is wrong |
 |
|
Evening all. My trusty pizza delivery bike has come over all Chinese.
Sometimes the indicators don't flash and instead emit a constant light (until turned off) and the flasher unit remains silent, rather than the deafening clicks.
It started around the new year after I replaced all the bulbs (bike is 2.5 years and done 3 winters). I replaced like for like except the sidelight, I only had a 5w wedge rather than 3w.
Then it rained for the next 2 weeks solid. I was riding through 6" of water, then the bike was sitting in the open all day getting pissed on.
Then I got first occurrence of stuck indicators.
I thought it was water. Bought a can of WD40 and sprayed the flasher relay + connectors. This seemed to fix the problem, confirming in my mind it was water related.
I rode home in the wet, in the morning I had stuck indicators again (but only after 5mins).
Cleaned the relay with WD40 and wrapped it in plastic bag. Sorted. Worked for 2 days, then stuck indicators again.
- Bike is 2.5 years old (3 winters) as is the tiny 5ah Chinese battery.
- It's used daily, but only 3.5 miles each way, not much of a run.
- Replaced all bulbs with correct wattages, except sidelight which is 5w wedge not 3w.
I now have 3w wedge bulb and will fit tomorrow to replace the 5w.
I have a multimeter and would like to test battery. Battery is compatible with YUASA – YB5L-B on the YBR125. What should I see to know if the battery is ok or not in terms of output on the multimeter?
Depending on the reading I thought I'd take it out the bike and stick it on the Optimate tonight and leave it for 24 hours.
Thanks for any advice. I'm even worse with electrics than mechanics....if that were even possible  |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Islander |
This post is not being displayed .
|
 Islander World Chat Champion

Joined: 05 Aug 2012 Karma :    
|
 Posted: 20:15 - 01 Mar 2014 Post subject: |
 |
|
You should see somewhere around 12.5v with nothing switched on.
It's likely to be down to corrosion on connectors - have a look at the relay and its connectors and any other connectors you suspect and clean them up if necessary. A thin coating of vaseline will help prevent further corrosion and prevent water ingress.  |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Pigeon |
This post is not being displayed .
|
 Pigeon World Chat Champion

Joined: 27 Sep 2012 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Islander |
This post is not being displayed .
|
 Islander World Chat Champion

Joined: 05 Aug 2012 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Pigeon |
This post is not being displayed .
|
 Pigeon World Chat Champion

Joined: 27 Sep 2012 Karma :    
|
 Posted: 01:51 - 02 Mar 2014 Post subject: |
 |
|
Thanks Islander, wow at £3 it would be rude not to
I'll leave the 5w sidelight in, as it's more useful / noticeably brighter than the 3w.
In terms of relays needing to be able to handle low wattages, I noticed there were a lot of units for LED's such as this one
Out of curiosity, would this have been suitable for my 10w due to its wide operating range? Or are they different beasts. |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Islander |
This post is not being displayed .
|
 Islander World Chat Champion

Joined: 05 Aug 2012 Karma :    
|
 Posted: 03:01 - 02 Mar 2014 Post subject: |
 |
|
Yep that would have worked too.
The key is that it's electronic as opposed to electromechanical.
Electromechanical relays rely on a specific load to heat up coil, this in turn causes a bimetallic strip to bend and that breaks the contact. As the load is off, the strip cools and returns to its original shape which makes the contact again. This causes it to heat up and bend... and so on. Too small a load and you don't heat the strip enough so it either flashes very slowly or not at all.
An electronic relay uses a timing circuit that doesn't care about the load so as long as you remain within the actual contact ratings (and that's just to stop them from burning out over time), you'll have no problems at all.  |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Pigeon |
This post is not being displayed .
|
 Pigeon World Chat Champion

Joined: 27 Sep 2012 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
Old Thread Alert!
The last post was made 12 years, 263 days ago. Instead of replying here, would creating a new thread be more useful? |
 |
|
|