|
|
| Author |
Message |
| gavbriggs |
This post is not being displayed .
|
 gavbriggs Crazy Courier
Joined: 11 Jun 2013 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| stirlinggaz |
This post is not being displayed .
|
 stirlinggaz World Chat Champion

Joined: 22 Jul 2007 Karma :    
|
 Posted: 14:29 - 24 Feb 2014 Post subject: |
 |
|
hi,
i dont see why you would need a full bank of carbs, just because they have ONE seized pilot screw.
they are usually made of a soft brass type metal (probably brass ) & drill out very easily.
you would need to be quite inept to f*ck the whole carb.
i go on about using cobalt drill bits all the time but even "normal" HSS drill bits should be enough.
if it were me, (i have a full set of cobalt drill bits & a drill) i'd start off drilling slowly, with the smallest drill you have (2 or 3mm is usually wee enough) & work up the drill sizes until the screw collapses on itself.
stay away from them "easy outs" snap one of them & your f*cked.
remove the remaining swarf & debris with airline or carb cleaner & then replace the pilot screw.
they usually cost around a tenner delivered. (with o-ring or spring depending on type of screw)
cheers,
GAZ |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| gavbriggs |
This post is not being displayed .
|
 gavbriggs Crazy Courier
Joined: 11 Jun 2013 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Bikercem |
This post is not being displayed .
|
 Bikercem Borekit Bruiser
Joined: 01 Sep 2013 Karma :     
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| _Iain_ |
This post is not being displayed because the poster is banned. Unhide this post / all posts.
|
 _Iain_ Banned

Joined: 01 Feb 2012 Karma :     
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| gavbriggs |
This post is not being displayed .
|
 gavbriggs Crazy Courier
Joined: 11 Jun 2013 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Pete. |
This post is not being displayed .
|
 Pete. Super Spammer

Joined: 22 Aug 2006 Karma :     
|
 Posted: 20:33 - 25 Feb 2014 Post subject: |
 |
|
Hwta were the symptoms Gav? One stuck pilot adjuster shouldn't make a set of carbs useless. Lumpy tickover perhaps, but then only if it's screwed in tight or blocked. I once bought a Fazer that had the pilot screws all wound in so hard that the needles had snapped off, but the PO was still riding it 100 miles a day. ____________________ a.k.a 'Geri'
132.9mph off and walked away. Gear is good, gear is good, gear is very very good  |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| gavbriggs |
This post is not being displayed .
|
 gavbriggs Crazy Courier
Joined: 11 Jun 2013 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| bodger |
This post is not being displayed .
|
 bodger Nova Slayer
Joined: 18 Apr 2012 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| gavbriggs |
This post is not being displayed .
|
 gavbriggs Crazy Courier
Joined: 11 Jun 2013 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Pete. |
This post is not being displayed .
|
 Pete. Super Spammer

Joined: 22 Aug 2006 Karma :     
|
 Posted: 18:07 - 27 Feb 2014 Post subject: |
 |
|
You can test the pilot circuit with some carb cleaner and a straw, or with an airline blower. If you can blow through the circuit it's working. ____________________ a.k.a 'Geri'
132.9mph off and walked away. Gear is good, gear is good, gear is very very good  |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| gavbriggs |
This post is not being displayed .
|
 gavbriggs Crazy Courier
Joined: 11 Jun 2013 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
Old Thread Alert!
The last post was made 12 years, 263 days ago. Instead of replying here, would creating a new thread be more useful? |
 |
|
|