Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


yamaha aerox

Reply to topic
Bike Chat Forums Index -> The Workshop
 Topic moved: from Biking News & Rumours to The Workshop by Korn (5 Mar 2014 - 17:39)
View previous topic : View next topic  
Author Message

danboy3322
L Plate Warrior



Joined: 05 Mar 2014
Karma :

PostPosted: 17:16 - 05 Mar 2014    Post subject: yamaha aerox Reply with quote

Hi, I have a 2003 YAMAHA AEROX i have a PM X-TECH cylinder Alu kit for it and a 21mm carb with a geanelli Exhaust pipe, I cannot quite get the jetting right. Can anybody give me and ideas as to what jet to use and the needle position please? thank you Thumbs Up .
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

moonzoomer
World Chat Champion



Joined: 01 Jul 2012
Karma :

PostPosted: 22:39 - 05 Mar 2014    Post subject: Re: yamaha aerox Reply with quote

danboy3322 wrote:
Hi, I have a 2003 YAMAHA AEROX i have a PM X-TECH cylinder Alu kit for it and a 21mm carb with a geanelli Exhaust pipe, I cannot quite get the jetting right. Can anybody give me and ideas as to what jet to use and the needle position please? thank you Thumbs Up .
Trial and error mate, no two bikes are the same but if in doubt run it rich instead of weak or even better just get a bigger bike and save yourself a lot of hassle and expense.
 Back to top
View user's profile Send private message You must be logged in to rate posts

evoboy
World Chat Champion



Joined: 20 Aug 2009
Karma :

PostPosted: 00:07 - 06 Mar 2014    Post subject: Reply with quote

Keep going up in jet size untill it bogs out at full throttle, then go back a size.

Set the needle clip to the middle.
____________________
Suzuki GT250 x7------- Fazer 600------CB250RS------Aprilia Rally 70----- Bandit 600

APT Motorcycles
 Back to top
View user's profile Send private message You must be logged in to rate posts

stirlinggaz
World Chat Champion



Joined: 22 Jul 2007
Karma :

PostPosted: 13:24 - 06 Mar 2014    Post subject: Reply with quote

evoboy wrote:
Keep going up in jet size untill it bogs out at full throttle, then go back a size.

Set the needle clip to the middle.

hi,
normal procedure is to start off with a main jet too big & work down until its correct.
i know this might result in a few quid wasted on main jets, but not as expensive as running at WOT with too small a main jet,

cheers,
GAZ
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

danboy3322
L Plate Warrior



Joined: 05 Mar 2014
Karma :

PostPosted: 16:22 - 06 Mar 2014    Post subject: YAMAHA AEROX Reply with quote

i have done the trial and error i run it rich to point where its choking like heck (forgot to mention im running practically open carb as im using a k&n air filter) and the pm xtech pistons are like £30.00 each and whilst it was running rich it literally welded the ring to the piston and scored right through up the piston (that may be down to the fact that the flywheel side main bearing collapsed and shards of metal went through the ports and then to the side of piston) but it still welded the ring when running rich.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

evoboy
World Chat Champion



Joined: 20 Aug 2009
Karma :

PostPosted: 19:45 - 07 Mar 2014    Post subject: Reply with quote

stirlinggaz wrote:
evoboy wrote:
Keep going up in jet size untill it bogs out at full throttle, then go back a size.

Set the needle clip to the middle.

hi,
normal procedure is to start off with a main jet too big & work down until its correct.
i know this might result in a few quid wasted on main jets, but not as expensive as running at WOT with too small a main jet,

cheers,
GAZ


You will do well to seize it just from one run in a lean state. It will show as lean as soon as you try to move off from a standstill as full throttle is nearly always needed to launch.

On a geared bike I would start rich and get leaner till the bike ran best with good plug colour. But for a scooter its far far easier to work the other way round.

For example. The race ped has a 21mm carb and a Athena HPR 70cc kit. The carb came with an 88main. The scooter would still run at full throttle on that jet. It now has a 100main and I'm still going bigger! Laughing
____________________
Suzuki GT250 x7------- Fazer 600------CB250RS------Aprilia Rally 70----- Bandit 600

APT Motorcycles
 Back to top
View user's profile Send private message You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 258 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.05 Sec - Server Load: 1.23 - MySQL Queries: 17 - Page Size: 49.79 Kb