Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


clutch wont engage / disengage after rebuild. Help :( Rotax

Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

Darkstar82
Borekit Bruiser



Joined: 12 Jan 2013
Karma :

PostPosted: 12:14 - 28 Apr 2014    Post subject: clutch wont engage / disengage after rebuild. Help :( Rotax Reply with quote

Well, my rebuild of my AF1 Futura is complete, she looks lovely, you can pop her in to neutral and start her, no problem. She sits there and purrs, a testiment to my fine mechanical skills...

as long as you dont want to go anywhere. Confused





Problem:
Starts in neutral and idles well, but, pull in clutch and step down a gear and the bike jolts, engine cuts. Its like starting the bike in gear even though the clutch feels firm.

Now, before I bolted the engine back up I checked the gears moved through their sequences and they do, 1 down, 5 up, .5 between 1st and second for neutral so I am praying to God above that I don't need to split my engine again to fix this.

Please help / give me hope.

Engine is two stroke, rotax 123,


Last edited by Darkstar82 on 14:48 - 28 Apr 2014; edited 1 time in total
 Back to top
View user's profile Send private message You must be logged in to rate posts

stirlinggaz
World Chat Champion



Joined: 22 Jul 2007
Karma :

PostPosted: 12:16 - 28 Apr 2014    Post subject: Reply with quote

hi,
does it have a side stand cut out switch?
likely to be something obvious like that,
cheers,
GAZ
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Darkstar82
Borekit Bruiser



Joined: 12 Jan 2013
Karma :

PostPosted: 12:31 - 28 Apr 2014    Post subject: Reply with quote

Hi there stirlinggaz, thanks for the reply,

Not that I am aware of, the bikes 25 years old, Aprilia AF1 Futura (the RS prototype range before RS became main product in 92) hence I don't believe it has electronics like that, The clutch is definitely stiff enough so I`m at a loss (and mortally depressed after spending 2 months rebuilding her in my dining room... )
 Back to top
View user's profile Send private message You must be logged in to rate posts

SQL
World Chat Champion



Joined: 08 Aug 2012
Karma :

PostPosted: 14:06 - 28 Apr 2014    Post subject: Reply with quote

Is there a little ball bearing that goes in the hole in the middle of the clutch that you have forgot to put in?
 Back to top
View user's profile Send private message Visit poster's website You must be logged in to rate posts

Darkstar82
Borekit Bruiser



Joined: 12 Jan 2013
Karma :

PostPosted: 14:44 - 28 Apr 2014    Post subject: Reply with quote

SQL wrote:
Is there a little ball bearing that goes in the hole in the middle of the clutch that you have forgot to put in?




possibly.... i do recall playing with a mystery ball bearing on a side board.


if for example, I have and its gone up the hoover, can i use any same sized ball bearing or do I have to have it machined over the course of five years by minions at aprilia, then pay £500 for said ball bearing to be purchased and transported by camel from Italy to the UK via baghdad. ?

^ youd almost think Ive had to buy Aprilia parts before...
 Back to top
View user's profile Send private message You must be logged in to rate posts

SQL
World Chat Champion



Joined: 08 Aug 2012
Karma :

PostPosted: 15:14 - 28 Apr 2014    Post subject: Reply with quote

Darkstar82 wrote:
SQL wrote:
Is there a little ball bearing that goes in the hole in the middle of the clutch that you have forgot to put in?




possibly.... i do recall playing with a mystery ball bearing on a side board.


if for example, I have and its gone up the hoover, can i use any same sized ball bearing or do I have to have it machined over the course of five years by minions at aprilia, then pay £500 for said ball bearing to be purchased and transported by camel from Italy to the UK via baghdad. ?

^ youd almost think Ive had to buy Aprilia parts before...


Personally i'd put anything that fits but many kittens may die as a direct result, might be worth checking the EPC photos to see if it has one you missed
 Back to top
View user's profile Send private message Visit poster's website You must be logged in to rate posts

thomp1983
Crazy Courier



Joined: 05 Feb 2011
Karma :

PostPosted: 15:20 - 28 Apr 2014    Post subject: Reply with quote

Is the clutch cable adjusted correctly? Can you start the bike with the clutch pulled in and 1st selected?
 Back to top
View user's profile Send private message You must be logged in to rate posts

Kickstart
The Oracle



Joined: 04 Feb 2002
Karma :

PostPosted: 19:11 - 28 Apr 2014    Post subject: Reply with quote

Hi

They quite often can do that if stood for a while. So first thing to check is that if you hold the brake on, give it a few revs (not that many, maybe 4k or so) and knock it into gear see if it frees the clutch off.

There is no cutout on the side stand. Indeed you can start the bike in gear with the stand down (not recommended).

However after that I would suggest the clutch adjustment. The adjuster at the lever is of little importance compared to the one under the clutch cover. Slacken the adjuster at the lever. Undo the cover in the middle of the clutch cover. Undo the locknut in there and undo the screw in the middle a bit. then lightly tighten it until you feel resistance (ie, when it starts to push against the clutch springs), then back it off half a turn or so. Then hold the adjuster steady and tighten up the lock nut. Replace the cover and then adjust at the lever to suit yourself.

Failing that you have probably got something wrong in assembling the clutch.

All the best

Keith
____________________
Traxpics, track day and racing photographs - Bimota Forum - Bike performance / thrust graphs for choosing gearing
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

andy_uk
World Chat Champion



Joined: 13 Aug 2011
Karma :

PostPosted: 20:48 - 28 Apr 2014    Post subject: Reply with quote

Kickstart wrote:
Hi

They quite often can do that if stood for a while. So first thing to check is that if you hold the brake on, give it a few revs (not that many, maybe 4k or so) and knock it into gear see if it frees the clutch off.

+1 to this!
While your engine was in bits, how did you store the clutch?
If it was stored 'dry' then there's a good chance that the plates have bonded.

if Keith's remedy doesn't work, then you may need to take the clutch basket out again. (drain oil, remove side panel - no engine split required)
Once it's out, dismantle it, soak the plates in oil overnight, re-assemble & refit. From what I can remember, there isn't a ball bearing that can easily come out (although mine's a Rotax122, so it could be different).
____________________
Aprilia Classic 125, GS500E, ER5-A1, ER5-C4, ER6 & an XJ6 project frame...
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Darkstar82
Borekit Bruiser



Joined: 12 Jan 2013
Karma :

PostPosted: 20:11 - 29 Apr 2014    Post subject: Reply with quote

As always your inputs magic, Will try the last two posts in order and see how it goes, clutch was indeed stored dry, i was trying to separate the plates, had to slide them off...

turns out the ball bearing is part of the basket and cant fall out.

the bolts that go in to the springs and bolt into the cradle, should these be tightened all the way in or am I supposed to leave some height ?

cheers.
 Back to top
View user's profile Send private message You must be logged in to rate posts

andy_uk
World Chat Champion



Joined: 13 Aug 2011
Karma :

PostPosted: 21:01 - 29 Apr 2014    Post subject: Reply with quote

Darkstar82 wrote:

the bolts that go in to the springs and bolt into the cradle, should these be tightened all the way in or am I supposed to leave some height ?

cheers.


All the way in I would think (that's what I did), otherwise they could come loose.
If you have a Haynes (or similar) manual, it should give you a torque for them.

Just googled it and it's apparently 80NM for the 123.
____________________
Aprilia Classic 125, GS500E, ER5-A1, ER5-C4, ER6 & an XJ6 project frame...
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 203 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.06 Sec - Server Load: 0.44 - MySQL Queries: 14 - Page Size: 72.08 Kb