Help & FAQs    Search BCF    Members    Groups    Events Calendar
Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


Brake pads and calipers

 Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

Whosthedaddy
Super Spammer



Joined: 11 Dec 2005
Karma :
PostPosted: 15:58 - 04 Oct 2007    Post subject: Brake pads and calipers Reply with quote
When the ZX7R was serviced the mechanic noted that the right hand brake pads moved about within the caliper, squeeze the lever and they bite onto the disc. He was a little confused as was I, although you can hear a clunk-clunk noise as the wheel spins and the pads knock about. As they worked no more was said, but it is concerning me.

The front brake is not what I would expect and maybe if they weren't loose it would respond a lot better rather than the last few mm of squeeze on the lever.

Had a quick look today and the pads on both sides in both calipers jiggle about? The hole where the spindle goes through the pads is quite large compared to the diameter of the spindle and the tension plate that fits on top can only go one way.

How much pad movement is allowed in calipers?

Should I be concerned or am I right to be confused?
____________________
Current : MSX 125 Past : CBR 900RR Monkeybike : c50 LAC : ZXR750 H2 : FZR600 : ZX7R P3 : YW100 : TRX850: Trophy 900 T309 : GSXR 600 L0: Monkeybike : XJ6S Whosthedaddy
 Back to top
View user's profile Send private message You must be logged in to rate posts

TUG
World Chat Champion



Joined: 12 May 2007
Karma :
PostPosted: 13:53 - 05 Oct 2007    Post subject: Reply with quote
there should only be a few mm of play, my pads dont move much on my fzr but then again it might be different on the ninja, are you a member of a ninja owners forum? i'd ask them as they'd know best. it is a bit strange that, maybe it is causing a bit of loose braking that your not getting the full potential of. i'd look into it personally.
____________________
Haz ER-5, innit!
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

alun111
World Chat Champion



Joined: 31 May 2007
Karma :
PostPosted: 14:31 - 05 Oct 2007    Post subject: Reply with quote
Do you mean they move up and down on the pin/s that hold/s them in? Or do you mean they move side to side towards the pistons?

Get some pics up if you can, always helps.
 Back to top
View user's profile Send private message You must be logged in to rate posts

Whosthedaddy
Super Spammer



Joined: 11 Dec 2005
Karma :
PostPosted: 14:58 - 05 Oct 2007    Post subject: Reply with quote
alun111 wrote:
Do you mean they move up and down on the pin/s that hold/s them in? Or do you mean they move side to side towards the pistons?

Get some pics up if you can, always helps.


Up and down.
____________________
Current : MSX 125 Past : CBR 900RR Monkeybike : c50 LAC : ZXR750 H2 : FZR600 : ZX7R P3 : YW100 : TRX850: Trophy 900 T309 : GSXR 600 L0: Monkeybike : XJ6S Whosthedaddy
 Back to top
View user's profile Send private message You must be logged in to rate posts

TUG
World Chat Champion



Joined: 12 May 2007
Karma :
PostPosted: 15:07 - 05 Oct 2007    Post subject: Reply with quote
sounds like bad pads, like someones made the holes in the top bigger or something, does it look like its been filed? or anything dodgey?
____________________
Haz ER-5, innit!
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Whosthedaddy
Super Spammer



Joined: 11 Dec 2005
Karma :
PostPosted: 15:13 - 05 Oct 2007    Post subject: Reply with quote
XlonewolfX wrote:
sounds like bad pads, like someones made the holes in the top bigger or something, does it look like its been filed? or anything dodgey?


Nothing dodgy, but on 1st inspection it looked like the spindle hole was elongated and not round.

Could remove one and compare with a new one from the shops just to make sure.
____________________
Current : MSX 125 Past : CBR 900RR Monkeybike : c50 LAC : ZXR750 H2 : FZR600 : ZX7R P3 : YW100 : TRX850: Trophy 900 T309 : GSXR 600 L0: Monkeybike : XJ6S Whosthedaddy
 Back to top
View user's profile Send private message You must be logged in to rate posts

alun111
World Chat Champion



Joined: 31 May 2007
Karma :
PostPosted: 15:19 - 05 Oct 2007    Post subject: Reply with quote
On my rear caliper there are spring clip things that fit over the top of the pads near the holes (however, I'm not sure what these are for). Have you got a manual or could you find a parts diagram and see if there are any pieces missing/or fitted incorrectly.
 Back to top
View user's profile Send private message You must be logged in to rate posts

Whosthedaddy
Super Spammer



Joined: 11 Dec 2005
Karma :
PostPosted: 15:29 - 05 Oct 2007    Post subject: Reply with quote
alun111 wrote:
Have you got a manual or could you find a parts diagram and see if there are any pieces missing/or fitted incorrectly.


No, but doesn't appear anything to be missing, just one pin and a tension plate on top. The calipers on the FZR had the tension plate fit under the brake pad pins so pushing down on them and preventing them from moving.

https://www.ronayers.com/fiche/400_0404/front_brake/front_brake.bmp
____________________
Current : MSX 125 Past : CBR 900RR Monkeybike : c50 LAC : ZXR750 H2 : FZR600 : ZX7R P3 : YW100 : TRX850: Trophy 900 T309 : GSXR 600 L0: Monkeybike : XJ6S Whosthedaddy
 Back to top
View user's profile Send private message You must be logged in to rate posts

TUG
World Chat Champion



Joined: 12 May 2007
Karma :
PostPosted: 15:34 - 05 Oct 2007    Post subject: Reply with quote
i think that its been reshaped due to vibrations or forcer from braking, maybe they had a bit missing out the pad like a chip or something and have just moved that way, or maybe where all totally off and there sposed to move like this, the only way to find out is to ask another owner.
____________________
Haz ER-5, innit!
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
Old Thread Alert!

The last post was made 18 years, 341 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT + 1 Hour
Page 1 of 1

 
 You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 
Debug Mode: ON - Server: birks (www) - Page Generation Time: 0.07 Sec - Server Load: 0.66 - MySQL Queries: 13 - Page Size: 61.74 Kb