Tyre problems???

[craigT19]

hi,

My ninja keeps wheel spinning when i'm at full throttle in first and second gear, around 8K rpm..... and its getting annoying

Is this likely to be a problem with the bike?? or just that the tyres aren't up to the job? i'm running bridgestone 010's. i've done around 300 miles on them

either way i'm changing them for dragon evos
____________________
Bikes owned :- 2001 nsr125, 1999 zx6r, 2006 yzf-r1, 2009 xmax 250, 2012 yzf-r1, 2015 MT-07
Current bike : - 2016 MT-10
BCF member pops. sadly missed 1945-2003

[kev]

Unless the roads are very wet of icey there is no way a 600 will spin up a bt010 just off the throttle.

You will find its more like your clutch is slipping.

Lastly bt010`s are stickyer than dragon evo corsas.
____________________
20:02:36 Jammy-R6: any holes a goal
20:02:48 kev: even if its a hairy mans arse
20:02:56 Jammy-R6: hell yes

[craigT19]

well the roads are dry, the bike IS spinning the rear, and there is no way 010's are stickier than pirreli dragon super corsers LMAO!!!


ohh and its a new clutch, which is fine, i know its spinning out cos it happened alot last night whilst i was ridding with scotty_zx6r (pm him if u must), the back kept kicking out on bends.
____________________
Bikes owned :- 2001 nsr125, 1999 zx6r, 2006 yzf-r1, 2009 xmax 250, 2012 yzf-r1, 2015 MT-07
Current bike : - 2016 MT-10
BCF member pops. sadly missed 1945-2003

[kev]

Evo`s and super corsas are different tyres.
____________________
20:02:36 Jammy-R6: any holes a goal
20:02:48 kev: even if its a hairy mans arse
20:02:56 Jammy-R6: hell yes

[Jon]

Sounds like the clutch to me, I'm getting some clutch slip which at first felt like the wheel was spinning up.

[craigT19]

ok thx jon...ill get it in the garage before i go to france to get it looked at
____________________
Bikes owned :- 2001 nsr125, 1999 zx6r, 2006 yzf-r1, 2009 xmax 250, 2012 yzf-r1, 2015 MT-07
Current bike : - 2016 MT-10
BCF member pops. sadly missed 1945-2003

[Mr C]

does it spin in a straight line or are you just cack handed coming out of bends with too much gas

do you have any free play in the clutch lever
____________________
187.3bhp = 201mph

[craigT19]

yeah both but i happens mostly when i hit a bump or a cats eye etc...

and i have some play in my clutch lever....

i've spoken to a few guys on Mirc and most seem to think its a suspension problem
____________________
Bikes owned :- 2001 nsr125, 1999 zx6r, 2006 yzf-r1, 2009 xmax 250, 2012 yzf-r1, 2015 MT-07
Current bike : - 2016 MT-10
BCF member pops. sadly missed 1945-2003

[billy whizz]

sounds like a damping problem to me to, get it sorted mate before you get dumped in a ditch. what's probably going on is your back wheel is skipping under power nice light bike plus lots of power needs lots of control!
____________________
Here comes the summer!

[Kickstart]

Hi

Assuming it isn't the clutch (and when it bites again it could loosen the rear wheels grip) then I would say there is a problem with the rear suspension. Probably lost most of the damping, either compression or rebound (but check nobody has been fiddling with the adjusters), possibly with the spring would up too hard.

All the best

Keith
____________________
Traxpics, track day and racing photographs - Bimota Forum - Bike performance / thrust graphs for choosing gearing

[G]

Hmmmm.
Presuming it is the rear wheel spinning and not the clutch...
Supercorsa's will probably make it a lot worse while the tyre's cold and it's harder to get them warm. So do becareful with the right hand coming out of corners if it's doing it with 010s at the moment.

[Demonic69]

Checked the air pressures mate?
____________________
Back on a Blade. Just feels so right.

[Kris]

Maybe the garage slotted in a ZX-10 engine by mistake..


____________________
NSR125RR - ZXR750H1 - ZX9R E1 - GSF600S - GSF600SK3 - VFR400-NC30 - SV1000N - ST1100-R - CBR900RR-R - GSF1200SK5 - GSF600SK1 - VFR1200FA - GSXR1000K2 - ZZR1400 D8F
www.prisonplanet.com

[Robby]

Check your linkages - they would have all been undone to be transferred to a new engine and frame, so the shop could have done them up too tight or with too little lube, meaning your shock isn't moving much.

[craigT19]