Fazer undertray

[CHR15]

thought id tidy the fazer up a little bit, so ive bought an undertray, £30 delivered. bargin.
https://i939.photobucket.com/albums/ad233/chris-bracey/meh/DSCF1148.jpg

https://i939.photobucket.com/albums/ad233/chris-bracey/meh/DSCF1147.jpg

https://i939.photobucket.com/albums/ad233/chris-bracey/meh/DSCF1146.jpg


and 7 x 5 was a fiver.
https://i939.photobucket.com/albums/ad233/chris-bracey/meh/DSCF1150.jpg

anyway im going to fit it on saturday, in the mean time i need some creative ideas for a numberplate light.

any sugestions?
____________________
Turbocharged drag thing / project death weapon / GK73A
Ste: I'm not entirely sure how you'd go about verbally abusing someone with a potato but I'm sure it's possible.

[ms51ves3]

One L.E.D wired into the rear light.

[TUG]

R&G do some number plate lights, its just 3 super bright LEDs on a tab i think, or you can get those shit looking LED bolts. Or you could just run the bike without.
____________________
Haz ER-5, innit!

[CHR15]

its a 99 plate bike, will it pass an mot without a no. plate light?
____________________
Turbocharged drag thing / project death weapon / GK73A
Ste: I'm not entirely sure how you'd go about verbally abusing someone with a potato but I'm sure it's possible.

[The Artist]

It will if you take it to the place I did mine at. Awesome bloke

[YZFR1-Dave]

sweet, had a similar setup on my hornet..

They lights that fit are "shotgun " lights, they should act as a number plate light aswell..


find what you need here
https://www.jesterstrickbits.co.uk/acatalog/Tail_Lights.html

[alun111]

[CHR15]

it already came with lights, 2 little circulair ones. there solid reds but where they fit is further back than the plate.

does it actualy have to work in the dark, or will the fact there is a white led there suffice?
____________________
Turbocharged drag thing / project death weapon / GK73A
Ste: I'm not entirely sure how you'd go about verbally abusing someone with a potato but I'm sure it's possible.

[ms51ves3]

Out of interest, where did you get the plate from?

[MonkeyKnuckle]

My understanding is that it needs to have a working number plate light in order to pass an MOT.
____________________
MKGaming.com
2000 Honda CBR600F - Sold! 2003 Honda CBR600RR - Current!

[CHR15]

numberplate came from ebay, its not exactly legal. but ive had worse. what is it anyway, 30 quid fine?

im sure i can knock something up thatl work ok, and ill speak to you later (allymoss) about the mot place.
____________________
Turbocharged drag thing / project death weapon / GK73A
Ste: I'm not entirely sure how you'd go about verbally abusing someone with a potato but I'm sure it's possible.

[CHR15]

started stripping.

https://i939.photobucket.com/albums/ad233/chris-bracey/meh/DSCF1155.jpg
https://i939.photobucket.com/albums/ad233/chris-bracey/meh/DSCF1153.jpg

basicaly i cut the rear mudgaurd, ecu tray, and all that crap off using a dremmel and hacksaw blade.

till this

https://i939.photobucket.com/albums/ad233/chris-bracey/meh/DSCF1157.jpg

https://i939.photobucket.com/albums/ad233/chris-bracey/meh/DSCF1158.jpg


then drilled and fitted the read lights

https://i939.photobucket.com/albums/ad233/chris-bracey/meh/DSCF1160.jpg


then refitted the tail

https://i939.photobucket.com/albums/ad233/chris-bracey/meh/DSCF1163.jpg


test fit

https://i939.photobucket.com/albums/ad233/chris-bracey/meh/DSCF1162.jpg


then i finished it, but my camera went dead. im going to wash it tomorrow so ill get some nice clean shots of it then.

it wasnt as hard as i thought, and looks quite good tbh. took about 3 hours in all.
____________________
Turbocharged drag thing / project death weapon / GK73A
Ste: I'm not entirely sure how you'd go about verbally abusing someone with a potato but I'm sure it's possible.

[TUG]

That looks shit. Well done.
You didn't mock the indi's up and just drilled away eh? A plate holder would of done you some good but nevermind, looked better standard imo.
____________________
Haz ER-5, innit!

[CHR15]

meh, i think it looks ok.

the indis were mocked up, matched on either side so there in the same place.

they had to be like that to clear the tail unit.

im going to need to fit a metal tail tidy, so i can rifit the 9x6 for an mot.

when i do that, ill fit the indis to it, so there level.
____________________
Turbocharged drag thing / project death weapon / GK73A
Ste: I'm not entirely sure how you'd go about verbally abusing someone with a potato but I'm sure it's possible.

[TUG]

It will look miles better like that mate, Get one of those sliding ones that adjust to plate size, that way you can keep your tail tidy...
____________________
Haz ER-5, innit!

[CHR15]

[TUG]

am sure motrash make one, sorry motrax.
There you go you lazy get.
____________________
Haz ER-5, innit!

[Gazdaman]

Agreed, you need a tail tidy which'll make the indicators sit nicely straight.

I think it looks good.

Gaz