Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


Replacing leaking lead 'T' water pipe with copper

Reply to topic
Bike Chat Forums Index -> Dear Auntie BCF...
View previous topic : View next topic  
Author Message

G
The Voice of Reason



Joined: 02 Feb 2002
Karma :

PostPosted: 15:11 - 18 Jan 2013    Post subject: Replacing leaking lead 'T' water pipe with copper Reply with quote

Got a leaking hot water pipe - the leak is coming from a 't junction' area.
I believe the pipe is lead.

Haven't measured, but think it's around 1" lead, which at the moment is then soldered on to a 22mm copper which goes in to the top of the hot water tank.

Anything special to look out for if I'm to replace it with copper (or plastic, etc) - you can get special adaptors, so presuming they are the right size, thinking it should be fairly easy?
 Back to top
View user's profile Send private message You must be logged in to rate posts

Al
World Chat Champion



Joined: 26 Feb 2006
Karma :

PostPosted: 16:07 - 18 Jan 2013    Post subject: Reply with quote

You can get compression type adaptors called 'leadlocks'
Lead pipe is normally measured in weight ie 7lb, 9lbs ect but I'm not sure what that equates to in size.
Just cut the pipe nice and straight with a hacksaw and file the edges smooth, don't over tighten the fitting as it can crush the lead and cause it to leak you just want it to bite in, maybe use some ptfe tape on the joint to help it seal.
____________________
Yamaha FZR400RR 3tj
My Instagram Thingy
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Ariel Badger
Super Spammer



Joined: 02 Dec 2006
Karma :

PostPosted: 18:07 - 18 Jan 2013    Post subject: Reply with quote

Cut lead pipe square. Bell it out with a turnpin or home made conical 'thing' to take copper pipe. Clean up the cut end and inside pipe with shave hook/wire wool etc.
Apply light coating of flux to inside of lead. 'Tin' copper pipe before inserting into lead by applying flux and solder to end of pipe beyond insertion depth.
Flux copper lightly again and insert copper pipe into lead.Heat copper with blowtorch and using bar of Grade D solder (in same manner as normal solder) caress the side of the copper with it and watch it fill the cavity. Using wiping cloth (moleskin soaked in tallow ) shape the lead into something resembling a wiped joint that the old boys were so proud of.
____________________
Bikers make great organ donors, get 115 on your licence today.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Raffles
World Chat Champion



Joined: 14 Apr 2009
Karma :

PostPosted: 22:23 - 18 Jan 2013    Post subject: Reply with quote

Do you have access to the whole length of lead piping? If so then it would probably be easier to simply replace the entire section with copper pipe and suitable fittings.
____________________
A good loser will always be a loser.
 Back to top
View user's profile Send private message You must be logged in to rate posts

G
The Voice of Reason



Joined: 02 Feb 2002
Karma :

PostPosted: 23:42 - 18 Jan 2013    Post subject: Reply with quote

Cheers, had found the 'leadlocks' and decided that was probably the easiest way.

I had misplaced my blow torch, but we now have one (to be fair, mine is likely somewhere obvious if I look.)
Never soldered pipework before, so wasn't sure I wanted to start on this.

I don't have access to all the copper piping - both bits after the 'T' disappear in to the walls after a bit unfortunately.
 Back to top
View user's profile Send private message You must be logged in to rate posts

Raffles
World Chat Champion



Joined: 14 Apr 2009
Karma :

PostPosted: 00:13 - 19 Jan 2013    Post subject: Reply with quote

G wrote:
Never soldered pipework before, so wasn't sure I wanted to start on this.

Soldering copper pipework is one of the easiest (and yet most feared) DIY tasks. It is especially easy if ''Yorkshire'' fittings are used.
If you are a soldering virgin, you should not attempt to pop your cherry with a lead joint, as it will all end horribly.
____________________
A good loser will always be a loser.
 Back to top
View user's profile Send private message You must be logged in to rate posts

mentalboy
World Chat Champion



Joined: 05 May 2012
Karma :

PostPosted: 18:12 - 19 Jan 2013    Post subject: Reply with quote

And try not to breathe in fumes Exclamation
____________________
Make mine a Corona.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

smegballs
World Chat Champion



Joined: 28 Oct 2007
Karma :

PostPosted: 18:19 - 19 Jan 2013    Post subject: Reply with quote

Ariel Badger wrote:
Cut lead pipe square. Bell it out with a turnpin or home made conical 'thing' to take copper pipe. Clean up the cut end and inside pipe with shave hook/wire wool etc.
Apply light coating of flux to inside of lead. 'Tin' copper pipe before inserting into lead by applying flux and solder to end of pipe beyond insertion depth.
Flux copper lightly again and insert copper pipe into lead.Heat copper with blowtorch and using bar of Grade D solder (in same manner as normal solder) caress the side of the copper with it and watch it fill the cavity. Using wiping cloth (moleskin soaked in tallow ) shape the lead into something resembling a wiped joint that the old boys were so proud of.


Engineering Boner Status:

[✓] Boner
[_] No boner

Embarassed
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

G
The Voice of Reason



Joined: 02 Feb 2002
Karma :

PostPosted: 22:12 - 19 Jan 2013    Post subject: Reply with quote

All sorted now, ta.

Used a leadlock and leadline as the shop only had one of each.
 Back to top
View user's profile Send private message You must be logged in to rate posts
Old Thread Alert!

The last post was made 13 years, 304 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> Dear Auntie BCF... All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.12 Sec - Server Load: 0.59 - MySQL Queries: 13 - Page Size: 61.05 Kb