NSR 125-F 1998 CLUTCH PROBLEM!

[ste.cameron25]

Hello after some messing about with my clutch plates I finally got new plates and friction plates also springs. After fitting then as manual said to do so my clutch does not work as soon as I put clutch in and knock it into 1st it stalls I have tried and tried...starting to give up it just seems as if the clutch wasn't ther and Iam pulling the clutch lever for nothing I have had help off alain followed his instructions and still no joy anyone here can tel me what Iam doin Rong or if I have missed something cheers
____________________
If you carnt make it then buy it..

[stirlinggaz]

hi,
did you put the new plates in just like the old ones?
most clutches i have done, the last plate should be off-set, unlike all the other ones,
cheers,
GAZ

[ste.cameron25]

Hello I soaked then in oil and followed the manual on how to install them it seen as if iam missing something
____________________
If you carnt make it then buy it..

[bypass2]

any play in the cabble or not enough or to much. or the release lever engine end

[ste.cameron25]

No free play I have tried everything slack tight medium and still no joy
____________________
If you carnt make it then buy it..

[Nobby the Bastard]

Did you replace all the bits that you took out? Sounds like that the clutch isn't working because something is missing.
____________________
trevor saxe-coburg-gotha:"Remember this simple rule - scooters are for men who like to feel the breeze on their huge, flapping cunt lips."
Triumph Sprint ST 1050

[ste.cameron25]

Yes everything
____________________
If you carnt make it then buy it..

[Nobby the Bastard]

In the right place?
____________________
trevor saxe-coburg-gotha:"Remember this simple rule - scooters are for men who like to feel the breeze on their huge, flapping cunt lips."
Triumph Sprint ST 1050

[ste.cameron25]

Yes as the manual suggested for installing new clutch
____________________
If you carnt make it then buy it..

[bypass2]

what about the correct fitting of the anti-judder spring

[ste.cameron25]

Yes I have done that example if you can understand my little way off describing them. \|
____________________
If you carnt make it then buy it..

[bypass2]

the way i see it in the ns125 book is this way i/

[ste.cameron25]

This is how I done it image below
____________________
If you carnt make it then buy it..

[bikenut]

check with cmsnl just to be sure.........not seen pics.............is there a ball in the mech on this bike, suspect not as suspect clutch release system all on the clutch side rather than cable mech on opposite side?? as i said i've not seen the pics

so clutch release all, on clutch side........check all your work, spacer missing from behind clutch or tween baslet and drum??

re check all your work.
____________________
nuts about bikes

[ste.cameron25]

Tried that and reinstalled the clutch 4 times nothings missing everything's placed as its suppose to be am really lost on this one...
____________________
If you carnt make it then buy it..

[bypass2]

is it a bike you have recently brought. or have you used it regular and it gone like it. did you use the proper grade oil

[ste.cameron25]

It's a project iam doin the engine has been sat for a while engine fun perfect just the clutch that's been a bitch!! I will take photos off the steps iam doin to assemble the clutch try and make it easy just in case I have missed something cheers everyone
____________________
If you carnt make it then buy it..

[bypass2]

not sure about yours i brought a bike been standing and the bar behind the release mechanism was missing called the pusher peice it was doing what yours is. also show some pics on the clutch cabble release engine end

[ste.cameron25]

Problem solved

Terns out I needed a extra washer on my clutch hub but thers oready one on the back manual says nout about that big thanks for everyone's help
____________________
If you carnt make it then buy it..

[bikenut]

is it shown in cmsnl???????????????????????? :karma:
____________________
nuts about bikes

[ste.cameron25]

Where the clutch gos into the hub I needed a extra washer for some reason
____________________
If you carnt make it then buy it..