Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


Would you buy this used engine?

Reply to topic
Bike Chat Forums Index -> The Workshop Goto page 1, 2  Next
View previous topic : View next topic  
Author Message
_Iain_ This post is not being displayed because the poster is banned. Unhide this post / all posts.

MarJay
But it's British!



Joined: 15 Sep 2003
Karma :

PostPosted: 09:33 - 25 Feb 2014    Post subject: Reply with quote

Second hand two stroke engines are rarely worth it as you need to strip them down and inspect them anyway. By the time you do that you might as well rebuild it, or have rebuilt the original motor.

It does look clean, but it's the crank that you need to worry about. The bores also look like they need a hone, they are far too smooth. {edit} There is also a fair bit of scoring there... definitely compression test it!{edit} If you leave a two stroke engine in a damp garage over the winter, water vapour will get into the bottom end via the transfer ports and exhaust port and causes the roller bearings to rust. This makes the bottom end scrap in very short order, especially when run after being stood for a long time. This is really why a second hand two stroke is such a difficult proposition.
____________________
British beauty: Triumph Street Triple R; Loony stroker: KR1S; Track fun: GSXR750 L1; Commuter Missile: GSX-S1000F; Cheap project: CBR900RR FireBlade
Remember kids, bikes aren't like lego. You can't easily take a part from one bike and then fit it to another.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
_Iain_ This post is not being displayed because the poster is banned. Unhide this post / all posts.

skatefreak
World Chat Champion



Joined: 06 Feb 2010
Karma :

PostPosted: 15:36 - 25 Feb 2014    Post subject: Reply with quote

I recently rebuilt a 125 2stroke NSR engine that was left in a bin bag in a garden for god knows how long...
The bottom end big bearings were pantsed so replaced thoes and seals and got a new crank in there however the gearbox seem's decent.
Threw a piston kit in there as it was apart and happy days!

-Jvr
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Pete.
Super Spammer



Joined: 22 Aug 2006
Karma :

PostPosted: 18:41 - 25 Feb 2014    Post subject: Reply with quote

Piston has a granular appearance, which could be the samera but looks suspiciously like minor detonation damage. Looks like th episton has been picking up on the bore too. I reckon the cylinder could possibly be serviceable but the piston is most likely an iffy proposition for re-use. At the very least check the rings aren't tight in the grooves - another sure sign of detonation.
____________________
a.k.a 'Geri'

132.9mph off and walked away. Gear is good, gear is good, gear is very very good Very Happy
 Back to top
View user's profile Send private message Visit poster's website You must be logged in to rate posts

Shaft
World Chat Champion



Joined: 27 Dec 2010
Karma :

PostPosted: 19:59 - 25 Feb 2014    Post subject: Reply with quote

I'm not understanding.

Why would you buy an engine with the wrong gearbox for your bike, knowing you will need to totally rebuild it?

You already have an engine that needs rebuilding, all you're doing is spunking money for nothing.
____________________
Things get better with age; I'm close to being magnificent........
20 RE Interceptor, 83 Z1100A3, 83 GS650 Katana
WooHoo, I'm a Man Point Millionaire! https://www.bikechatforums.com/viewtopic.php?t=234035
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
_Iain_ This post is not being displayed because the poster is banned. Unhide this post / all posts.

P.addy
Red Rocket



Joined: 14 Feb 2008
Karma :

PostPosted: 10:07 - 26 Feb 2014    Post subject: Reply with quote

Turn up, view engine before handing over cash, spend the 30 secs whipping the head off Wink

To be fair, I'd have given up when you asked me to strip the engine, even if its minor parts because I have other things to do rather than drag out an engine that has been sat in the garage for 6 months init. Business is business Laughing
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
Vincent This post is not being displayed because the poster is banned. Unhide this post / all posts.
_Iain_ This post is not being displayed because the poster is banned. Unhide this post / all posts.

stevo as b4
World Chat Champion



Joined: 17 Jul 2003
Karma :

PostPosted: 12:57 - 26 Feb 2014    Post subject: Reply with quote

Totally agree here with Marjay.

But as you have explained that it's not just bearings, gaskets and seals you need to re-build the old engine, then all you need is a decent gearbox with all the gears in good condition, the selector forks and shafts and particulary the output shaft in good condition.

The top end is irrelevant anyway, as If its a plated bore, you want to be sending off for a re-plate and obviously you will want to have a full professional crank re-build and true done.

It's not what you were asking, but no way would I ever buy a second hand 2stroke lump to throw in and run as it is, due to several reasons not least of all a sat around doing nothing engine is likely to be fucked crank seal wise and that's if moisture has not got into the bottom end and pitted the crank pins etc.

If buying this motor gives you access to a decent head, and all the gearbox components other than bearings to re-build the old motor then go for it.

The head isn't a major issue anyway, as welding and machining can fix the old head at a cost.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
_Iain_ This post is not being displayed because the poster is banned. Unhide this post / all posts.

P.addy
Red Rocket



Joined: 14 Feb 2008
Karma :

PostPosted: 16:10 - 26 Feb 2014    Post subject: Reply with quote

I'm just crying at the price of parts Sad Think Fizzer rebuilt that R1 engine for ~£800. I would cry if my engine was wanged and required £400 to repair Sad
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
_Iain_ This post is not being displayed because the poster is banned. Unhide this post / all posts.

Pete.
Super Spammer



Joined: 22 Aug 2006
Karma :

PostPosted: 18:16 - 26 Feb 2014    Post subject: Reply with quote

Your 'contaminated' bearings can be flushed out. I recovered the bearings from my 1952 milling machine spindle and my tool 7 cutter grinder both were notchy with bits of hardened grease. They might be a wee bit loose afterwards but probably no worse then most bike gearbox bearings.
____________________
a.k.a 'Geri'

132.9mph off and walked away. Gear is good, gear is good, gear is very very good Very Happy
 Back to top
View user's profile Send private message Visit poster's website You must be logged in to rate posts
Vincent This post is not being displayed because the poster is banned. Unhide this post / all posts.
Vincent This post is not being displayed because the poster is banned. Unhide this post / all posts.

Shaft
World Chat Champion



Joined: 27 Dec 2010
Karma :

PostPosted: 21:42 - 26 Feb 2014    Post subject: Reply with quote

_Iain_ wrote:

What do you think? I'm 50/50 on it.




Well, the first thing I think is, feck me that's a lot of money for some bearings, so I would be doing what Pete says and trying to reclaim them.

Failing that, whip out the Vernier guage and measure them up for replacements from somewhere that doesn't say Honda on the packet.

Then I think this

https://www.ebay.co.uk/itm/HONDA-CR125-CYLINDER-HEAD-KZ4-1996-/400669924487?pt=UK_Motorcycle_Parts&hash=item5d49c9dc87

So now you're just buying gearbox internals and a pile of bits to gather dust in a box somewhere.

You've haven't said how much this new potential doorstop is.
____________________
Things get better with age; I'm close to being magnificent........
20 RE Interceptor, 83 Z1100A3, 83 GS650 Katana
WooHoo, I'm a Man Point Millionaire! https://www.bikechatforums.com/viewtopic.php?t=234035
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
_Iain_ This post is not being displayed because the poster is banned. Unhide this post / all posts.

Shaft
World Chat Champion



Joined: 27 Dec 2010
Karma :

PostPosted: 23:32 - 26 Feb 2014    Post subject: Reply with quote

You said a head is £150 and if it's as rare as you say, don't keep an eye on it, hit the fucking BIN button, before somebody else does.

Worst way, you get a part you dont use and can easily get your money back on.

As for this other engine, over 400 quid is a helluva punt; you've just saved £110 on the head and who knows what on the bearings, that just leaves the gearbox bits, which I'm sure could be picked up somewhere.

If it's a well used engine in karting, search the karting forums.
____________________
Things get better with age; I'm close to being magnificent........
20 RE Interceptor, 83 Z1100A3, 83 GS650 Katana
WooHoo, I'm a Man Point Millionaire! https://www.bikechatforums.com/viewtopic.php?t=234035
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
_Iain_ This post is not being displayed because the poster is banned. Unhide this post / all posts.

Shaft
World Chat Champion



Joined: 27 Dec 2010
Karma :

PostPosted: 00:34 - 27 Feb 2014    Post subject: Reply with quote

Hit the BIN button in the morning, then stall him til Friday, that's a good head and you know it's for nothing.

Then forget this other engine nonsense; if things are that tight, you need to get creative and rebuild your existing unit.

You're thinking of paying a fair bit of wedge for a motor that's being described as all good, so that means you're paying a premium; what you actually want is an engine that's fubar, with a good gearbox, which will be a lot cheaper.
____________________
Things get better with age; I'm close to being magnificent........
20 RE Interceptor, 83 Z1100A3, 83 GS650 Katana
WooHoo, I'm a Man Point Millionaire! https://www.bikechatforums.com/viewtopic.php?t=234035
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
Quornholio This post is not being displayed because the poster has bad karma. Unhide this post / all posts.

331X2
Crazy Courier



Joined: 10 Jul 2013
Karma :

PostPosted: 03:25 - 27 Feb 2014    Post subject: Reply with quote

+1 what Pete and Shaft said, for the length of time that they were 'contaminated' I'd make sure they were flushed completely free of debris and re-use them.
 Back to top
View user's profile Send private message You must be logged in to rate posts
_Iain_ This post is not being displayed because the poster is banned. Unhide this post / all posts.
Old Thread Alert!

The last post was made 12 years, 266 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Goto page 1, 2  Next
Page 1 of 2

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.10 Sec - Server Load: 0.66 - MySQL Queries: 13 - Page Size: 157.55 Kb