Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


Suzuki DR125S regulator problem...

Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

krisply
Derestricted Danger



Joined: 03 Jan 2014
Karma :

PostPosted: 19:14 - 03 Jan 2014    Post subject: Suzuki DR125S regulator problem... Reply with quote

hello folks,

I 'believe' my bike is a DR125S circa 1980 (V5 is not specific AND I cannot find it to confirm the reg date!)

the battery wasn't charging so I started to look at the regulator/rectifier and
found a load of corrosion but inadvertently broke off one of the five copper spades.
F*&K!
So I don't know whether I just had a connection issue or not.
Then I went looking for a replacement reg and found none looking exactly like it (no markings to go by) - it
has 5 copper spade connectors lined up flat along an edge, and bolt lobes projecting away from body of reg ie. the reg is not square but has these lobes either side of the cooling fins.

Could I replace with just about any 5-wire motorcycle reg/rect?
Does the order of the 3 phase wires from the stator matter to a rect/reg?
ie. can they be plugged in any which way?

your help is appreciated!
thanks,
kris
 Back to top
View user's profile Send private message You must be logged in to rate posts

WD Forte
World Chat Champion



Joined: 17 Jun 2010
Karma :

PostPosted: 20:09 - 03 Jan 2014    Post subject: Reply with quote

I've patched in various Rectifer regulators to other bikes without tears.
the order of the AC input wires isnt important.
So yes, its quite doable

I wouldnt use one from say a 50cc bike, one from a same size or bigger bike would be best
If you get one with no leads and just pins from a different bike,
Its wise to check the pin out to get all your existing leads going to the correct pins.
If it has 6 pins it may use an external sense wire.

A check with a meter will usually tell you what does what.
____________________
bikers smell of wee
 Back to top
View user's profile Send private message You must be logged in to rate posts

pepperami
Super Spammer



Joined: 17 Jan 2010
Karma :

PostPosted: 20:22 - 03 Jan 2014    Post subject: Reply with quote

Suzuki DR/gs 125 regulator from the breakers yard.

All the 125 four-stroke singles that are around at the moment, something must be compatible?
____________________
I am the sum total of my own existence, what went before makes me who I am now!
 Back to top
View user's profile Send private message You must be logged in to rate posts

krisply
Derestricted Danger



Joined: 03 Jan 2014
Karma :

PostPosted: 09:30 - 03 Feb 2014    Post subject: Reply with quote

thank you WD - a 5-wire type from ebay did the trick.
So the bike is up and running ... but almost limping along!
It's reasonable going down a very slight incline, will get to 60mph eventually, but the other way it has to crawl along in 2nd gear
and I can feel the engine lose power in hesitating steps.
I have already cleaned up the carb. Did not come across
any adjustment other than idle though, no air mixture screw for instance. Have I missed it?
Other than that I thought of just replacing the piston/ring/sparkplug.

Any ideas?
cheers,
kris
 Back to top
View user's profile Send private message You must be logged in to rate posts
Vincent This post is not being displayed because the poster is banned. Unhide this post / all posts.

krisply
Derestricted Danger



Joined: 03 Jan 2014
Karma :

PostPosted: 07:44 - 01 Mar 2014    Post subject: Reply with quote

I've got hold of a compression tester !
but the instructions talk about turning the engine over for 10 seconds.
presumably this is assuming an electric start.
I only have the kick-start - will I get a different result?

ta
kris
 Back to top
View user's profile Send private message You must be logged in to rate posts
Vincent This post is not being displayed because the poster is banned. Unhide this post / all posts.

robocog
Traffic Copper



Joined: 17 Apr 2009
Karma :

PostPosted: 09:01 - 08 Mar 2014    Post subject: Reply with quote

Hold throttle wide open (or remove carb)
make a note of the compression it gets to after a few kicks

If the reading is much lower than expected

pour a tablespoon of oil into the spark plug hole and repeat

If the compression is the same or very similar - the rings/piston/bore are possibly OK and its more likely a top end seal issue

If it makes a massive instant improvement the issue lies more likely in the piston sealing

(not 100% conclusive and they have to be seperated anyway to sort either end out)

Regards
Rob
____________________
Needs a bigger garage...
 Back to top
View user's profile Send private message Visit poster's website You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 258 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.05 Sec - Server Load: 0.34 - MySQL Queries: 13 - Page Size: 57.07 Kb