Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


Help with my ybr custom

Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

James2012
Derestricted Danger



Joined: 02 Mar 2014
Karma :

PostPosted: 19:59 - 02 Mar 2014    Post subject: Help with my ybr custom Reply with quote

First off I have little to no bike knowledge apart from how to ride it.. One problem is that my engine cuts out sometimes when sat in idle and sometimes when I pull away... It normally takes around ten minutes to do so... The starting revs are at 2 and then they slowly move down to 1.5 is this normal?? And the second problem is that when I went to change the air filter the box had lots of either water/ oil in with a white/creamy substance?? What could be causing that and are they linked???
Many thanks in advance
Regards Cool Cool Cool
____________________
Still trying to learn
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Rogerborg
nimbA



Joined: 26 Oct 2010
Karma :

PostPosted: 20:46 - 02 Mar 2014    Post subject: Reply with quote

Hi James.

Fuel injected model? I'd expect it to rev a bit higher when cold. The cutting out when warm is the idle dropping too low. Could be...

YBR Ric wrote:
Tickover adjustment will be by way of an anticlockwise twist of the small brass screw found on the right hand side of the injector body when engine is at normal working temperature. 1300-1500rpm is book recommendation for idle speed.
Try 1/2 turn first.


...or the temperature or lambda sensors being a bit screwy. I'll leave that to the YBR owners.

The crankcase vents into the air box, so you should expect to find some condensed vapours in there. If there's a lot in there, it could be that the air filter was manky and the engine has been sucking from the crankcase - my Burgman is notorious for doing it.

The mayonnaise you're seeing is an emulsion of oil and water. It's a symptom of doing short runs where the engine doesn't get up to high enough temperatures to boil the water out of it. There's nothing you can do about it except ride longer, or change the oil more regularly.
____________________
Biking is 1/20th as dangerous as horse riding.
GONE: HN125-8, LF-250B, GPz 305, GPZ 500S, Burgman 400 // RIDING: F650GS (800 twin), Royal Enfield Bullet Electra 500 AVL, Ninja 250R because racebike


Last edited by Rogerborg on 21:42 - 02 Mar 2014; edited 1 time in total
 Back to top
View user's profile Send private message You must be logged in to rate posts

James2012
Derestricted Danger



Joined: 02 Mar 2014
Karma :

PostPosted: 21:29 - 02 Mar 2014    Post subject: Reply with quote

Rogerborg wrote:
Hi James.

Fuel injected model? I'd expect it to rev a bit higher when cold. The cutting out when warm is the idle dropping too low. Could be...

YBR Ric wrote:
Tickover adjustment will be by way of an anticlockwise twist of the small brass screw found on the right hand side of the injector body when engine is at normal working temperature. 1300-1500rpm is book recommendation for idle speed.
Try 1/2 turn first.


...or the temperature or lambda sensors being a bit screwy. I'll leave that to the YBR owners.

The crankcase vents into the air box, so you should expect to find some condensed vapours in there. If there's a lot in there, it could be that the oil filter was manky and the engine has been sucking from the crankcase - my Burgman is notorious for doing it.

The mayonnaise you're seeing is an emulsion of oil and water. It's a symptom of doing short runs where the engine doesn't get up to high enough temperatures to boil the water out of it. There's nothing you can do about it except ride longer, or change the oil more regularly.



Yes it's fuel injected

If the idle is dropping too low do you know how to adjust it??? Thanks for your reply
____________________
Still trying to learn
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 263 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.05 Sec - Server Load: 0.67 - MySQL Queries: 13 - Page Size: 38.7 Kb