Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


Seized Up

Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

LanceMullin
L Plate Warrior



Joined: 03 Mar 2014
Karma :

PostPosted: 00:31 - 03 Mar 2014    Post subject: Seized Up Reply with quote

Hello
i'm new Smile
i got a problem with a bike the Rear Axle Bolt Seized Up wheel won't move
can't get the bolt out so i was thinking in replacing the whole swinging arm

or cut the bolt off

Lance
 Back to top
View user's profile Send private message You must be logged in to rate posts

SQL
World Chat Champion



Joined: 08 Aug 2012
Karma :

PostPosted: 00:34 - 03 Mar 2014    Post subject: Reply with quote

Drill a small pilot hole through the swing arm into the nut and you will then get it out easier
 Back to top
View user's profile Send private message Visit poster's website You must be logged in to rate posts

LanceMullin
L Plate Warrior



Joined: 03 Mar 2014
Karma :

PostPosted: 00:37 - 03 Mar 2014    Post subject: Reply with quote

SQL wrote:
Drill a small pilot hole through the swing arm into the nut and you will then get it out easier


ok cool sounds alot easier than to replace the whole swing arm

thank you again
 Back to top
View user's profile Send private message You must be logged in to rate posts
Vincent This post is not being displayed because the poster is banned. Unhide this post / all posts.
Vincent This post is not being displayed because the poster is banned. Unhide this post / all posts.

cb1rocket
World Chat Champion



Joined: 30 Jan 2010
Karma :

PostPosted: 10:16 - 03 Mar 2014    Post subject: Reply with quote

Get an impact driver on it. A bike shop may do this for beer money
____________________
Honda H100S2 Rebuild - https://www.bikechatforums.com/viewtopic.php?t=253852
 Back to top
View user's profile Send private message You must be logged in to rate posts

skatefreak
World Chat Champion



Joined: 06 Feb 2010
Karma :

PostPosted: 10:29 - 03 Mar 2014    Post subject: Reply with quote

weld on a breaker bar,
Get someone to stand on the rear break and jump away Wink

-Jvr
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
DiscoBiscuit This post is not being displayed because the poster is banned. Unhide this post / all posts.

m3-paul
Spanner Monkey



Joined: 03 Feb 2009
Karma :

PostPosted: 13:26 - 03 Mar 2014    Post subject: Reply with quote

Heat, wd40 and an impact gun. I had to undo the swing arm nut on my TZR a few weeks back. It took a 600nm rated snap-on impact gun with lots of heat with liberal doses of wd40 to get it off. I ended up rounding off the 22mm bolt and had to hammer on a 21mm socket and actually ran one battery down on the gun - I was at it that long!!

Bolts can be right gits to get off so I would get it to someone who has these tools.
____________________
Yamaha TZR250 - love the smell of TTS!!!!
CBR900RR Fireblade - so much fun
 Back to top
View user's profile Send private message Visit poster's website You must be logged in to rate posts

SQL
World Chat Champion



Joined: 08 Aug 2012
Karma :

PostPosted: 13:49 - 03 Mar 2014    Post subject: Reply with quote

Vincent wrote:
SQL wrote:
Drill a small pilot hole through the swing arm into the nut and you will then get it out easier


'Never heard this one before......wherabouts in the swingarm do you have to drill? And into what nut?


Mine was solid, tried heat, plus gas, sledgehammer couldn't get it to move at all.

Drilled through the engine mounting point into the swingarm spindle and put a touch of ACF 50 in there, couple of whacks while turning and bobs your uncle.

Thats if the swing arm goes through the engine.
 Back to top
View user's profile Send private message Visit poster's website You must be logged in to rate posts
Vincent This post is not being displayed because the poster is banned. Unhide this post / all posts.

SQL
World Chat Champion



Joined: 08 Aug 2012
Karma :

PostPosted: 15:28 - 03 Mar 2014    Post subject: Reply with quote

I totally read the first post I did Shifty

to do that id be tempted to use a 9" grinder with skinny cutting discs if I couldn't budge it at all but only as a last resort.
 Back to top
View user's profile Send private message Visit poster's website You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 262 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.05 Sec - Server Load: 0.41 - MySQL Queries: 13 - Page Size: 72.88 Kb