|
|
| Author |
Message |
| ice.shark |
This post is not being displayed .
|
 ice.shark Nova Slayer
Joined: 06 Apr 2013 Karma :     
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| ice.shark |
This post is not being displayed .
|
 ice.shark Nova Slayer
Joined: 06 Apr 2013 Karma :     
|
 Posted: 21:57 - 03 Mar 2014 Post subject: |
 |
|
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Kickstart |
This post is not being displayed .
|
 Kickstart The Oracle

Joined: 04 Feb 2002 Karma :     
|
 Posted: 22:47 - 03 Mar 2014 Post subject: |
 |
|
Hi
Unless the clutch is dragging very badly it shouldn't stall when you put it in gear.
How did you adjust the clutch? Should slacken the cable off at the bars, undo the lock nut in the middle of the clutch, undo the screw and then gently tighten it until it just starts to have resistance (ie, as it starts to push on the clutch), then undo it a bit (from memory half a turn) and hold it steady while you tighten up the lock nut. Then just adjust the cable at the bar to suit yourself.
All the best
Keith ____________________ Traxpics, track day and racing photographs - Bimota Forum - Bike performance / thrust graphs for choosing gearing |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| ice.shark |
This post is not being displayed .
|
 ice.shark Nova Slayer
Joined: 06 Apr 2013 Karma :     
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| _Iain_ |
This post is not being displayed because the poster is banned. Unhide this post / all posts.
|
 _Iain_ Banned

Joined: 01 Feb 2012 Karma :     
|
 Posted: 08:23 - 04 Mar 2014 Post subject: |
 |
|
Couldnt tell you about the problem, however Silkolene light gear oil is the stuff to use, if you look on the back of the bottle you'll see its actually 10w40.
If you'd put 75w80 in it you'd likely see some problems!  ____________________ Please be aware that the above post may be full of complete nonsense.
Riding: '07 KTM Duke II, Baotian BT49QT-20 Driving: '88 Volvo 340 |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| ice.shark |
This post is not being displayed .
|
 ice.shark Nova Slayer
Joined: 06 Apr 2013 Karma :     
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| _Iain_ |
This post is not being displayed because the poster is banned. Unhide this post / all posts.
|
 _Iain_ Banned

Joined: 01 Feb 2012 Karma :     
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| stirlinggaz |
This post is not being displayed .
|
 stirlinggaz World Chat Champion

Joined: 22 Jul 2007 Karma :    
|
 Posted: 18:56 - 04 Mar 2014 Post subject: |
 |
|
hi,
75/90 is what rotax & aprilia recommend, i always used "lite gear oil",(semi-synthetic) either rock-oil or silkolene with good results.
most folk forget that the clutch is adjustable at BOTH ends.
set the adjuster at 1/3rd out on the bars, & then adjust at engine end with box spanner supplied in the original bike tool-kit or use a socket (13mm? ) from a 1/4 inch socket set, hold it with mole-grips & adjust via the grub screw with a flat bladed screwdriver, iirc, & lock nut you'll find under the plastic cap on side of engine.
its all in the rotax 122 engine manual & the aprilia wsm, both of which are available for download for free.
cheers,
GAZ |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
Old Thread Alert!
The last post was made 12 years, 261 days ago. Instead of replying here, would creating a new thread be more useful? |
 |
|
|