Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


GPZ 500 oil leak hah

Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

Mez
Trackday Trickster



Joined: 13 Mar 2004
Karma :

PostPosted: 16:46 - 22 Apr 2014    Post subject: GPZ 500 oil leak hah Reply with quote

Riding home from work today I get to about 2 miles from home and some dimwits try to cut me off from merging by driving bumper to bumper, so I let rip and race ahead when I get chance (naughty, I know). Not long after I start to notice a smell that isn't normal.... actually, I don't remember at what point I noticed the smell... err... anyway I pull up outside my garage to see steam/smoke from RHS of the engine. Looks like oil is seeping from my clutch cover, dripping down onto the frame and eventually hitting the floor. I can only assume the gasket is gone... I don't have the time or heat-resistant skin to investigate further just yet.

Did my aggressive riding blow it? IIRC it has about 25k miles on the clock, should I expect it to go anyway for wear & tear? I've not had this bike long, and also I'm still a bit thick Karma
____________________
My deviantArt gallery - My Youtube profile
Honda CG125 -> Baotian BT49 -> AJS JS125 -> Honda CG125-> Kawasaki ZL400 -> Kawasaki GPZ500
 Back to top
View user's profile Send private message Send e-mail Visit poster's website You must be logged in to rate posts

stinkwheel
Bovine Proctologist



Joined: 12 Jul 2004
Karma :

PostPosted: 16:55 - 22 Apr 2014    Post subject: Reply with quote

Sometimes the mechanical seal behind the water pump lets go.

FIrst find where the oil is coming from. It's not always coming from where the most oil is. Cleaning the engine thoroughly will help. I've even scattered a small amount of cemet dust over the outside of an engine before to isolate an oil leak.

For example, if you're seeing oil on the clutch cover, it could easily be coming from a perforated oil filter and blowing back along the engine then trickling down the outside of the clutch cover.
____________________
“Rule one: Always stick around for one more drink. That's when things happen. That's when you find out everything you want to know.”
I did the 2010 Round Britain Rally on my 350 Bullet. 89 landmarks, 3 months, 9,500 miles.
 Back to top
View user's profile Send private message You must be logged in to rate posts

Mez
Trackday Trickster



Joined: 13 Mar 2004
Karma :

PostPosted: 17:03 - 22 Apr 2014    Post subject: Reply with quote

Yeah, I figured. From what I could quick glance, the oil appears to be seeping from the joint between the engine and clutch cover on the bottom edge. More investigation later.
____________________
My deviantArt gallery - My Youtube profile
Honda CG125 -> Baotian BT49 -> AJS JS125 -> Honda CG125-> Kawasaki ZL400 -> Kawasaki GPZ500
 Back to top
View user's profile Send private message Send e-mail Visit poster's website You must be logged in to rate posts

TheManWithThe...
Brolly Dolly



Joined: 30 Aug 2010
Karma :

PostPosted: 17:07 - 22 Apr 2014    Post subject: Reply with quote

is it similar looking to the oil leak in this thread?
https://www.bikechatforums.com/viewtopic.php?t=288563

I had a rhs oil leak on my er5 and assumed it was a bad clutch gasket, but a rebuild (not because of the leak) proved it wasn't, so now thinking it's the seal behind the water pump, as suggested above.
____________________
MBK Nitro 50, Sold. Kawasaki ER-5, Honda ST1100
"Anyone can jump a motorcycle! The trouble begins when you try to land it..."
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

TUG
World Chat Champion



Joined: 12 May 2007
Karma :

PostPosted: 04:44 - 23 Apr 2014    Post subject: Reply with quote

We have the same engine, leak in the same place maybe? Mine looks like it's coming from the oil pressure tester port bolt but I can't be 100% sure, it only leaks when the engine is running and the previous owner wondered if it's due to the oil pressure relief valve, im tempted to just replace all the gaskets to be honest and replace said valve.
____________________
Haz ER-5, innit!
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

stinkwheel
Bovine Proctologist



Joined: 12 Jul 2004
Karma :

PostPosted: 08:51 - 23 Apr 2014    Post subject: Reply with quote

The clutch is not pressurised (or it shouldn't be) so a leaky clutch cover gasket ought to leak all the time, not just when the engine is running (unless it is a very small leak which only happens when the oil is hot and runny).

So if it is leaking from there only when the engine is running it means the crankcase has become pressurised and therefore the crankcase breather is blocked. There is (obviously) a pressurised oilway behind the pressure guage blanking screw. Just a fiber gasket as I recall.

Anyway, an oil leak only when the engine is running pretty much has to be coming from a pressurised part of the engine. It shouldn't be from either if the side cover gaskets unless the breather is blocked.

Do have a good look at the oil filter. They can be hit by stones or rust through very easily and they are part of the pressurised oil circulation system. From experience, you can have a pinhole in your oil filter that mists oil out only at high revs. That oil can land up anywhere. In my case it was on my right foot and the mainstand.
____________________
“Rule one: Always stick around for one more drink. That's when things happen. That's when you find out everything you want to know.”
I did the 2010 Round Britain Rally on my 350 Bullet. 89 landmarks, 3 months, 9,500 miles.
 Back to top
View user's profile Send private message You must be logged in to rate posts

lihp
World Chat Champion



Joined: 22 Sep 2010
Karma :

PostPosted: 08:53 - 23 Apr 2014    Post subject: Reply with quote

stinkwheel wrote:
The clutch is not pressurised (or it shouldn't be) so a leaky clutch cover gasket ought to leak all the time, not just when the engine is running (unless it is a very small leak which only happens when the oil is hot and runny).

So if it is leaking from there only when the engine is running it means the crankcase has become pressurised and therefore the crankcase breather is blocked. There is (obviously) a pressurised oilway behind the pressure guage blanking screw. Just a fiber gasket as I recall.

Anyway, an oil leak only when the engine is running pretty much has to be coming from a pressurised part of the engine. It shouldn't be from either if the side cover gaskets unless the breather is blocked.

Do have a good look at the oil filter. They can be hit by stones or rust through very easily and they are part of the pressurised oil circulation system. From experience, you can have a pinhole in your oil filter that mists oil out only at high revs. That oil can land up anywhere. In my case it was on my right foot and the mainstand.


Good point, oil filter is due to be changed though.

Stink, TUG's description was misleading, the leak is from the main gallery bolt, where oil pressure is tested the bolt is a banjo bolt and is under pressure.
 Back to top
View user's profile Send private message You must be logged in to rate posts

lihp
World Chat Champion



Joined: 22 Sep 2010
Karma :

PostPosted: 08:57 - 23 Apr 2014    Post subject: Reply with quote

stinkwheel wrote:
The clutch is not pressurised (or it shouldn't be) so a leaky clutch cover gasket ought to leak all the time, not just when the engine is running (unless it is a very small leak which only happens when the oil is hot and runny).

So if it is leaking from there only when the engine is running it means the crankcase has become pressurised and therefore the crankcase breather is blocked. There is (obviously) a pressurised oilway behind the pressure guage blanking screw. Just a fiber gasket as I recall.

Anyway, an oil leak only when the engine is running pretty much has to be coming from a pressurised part of the engine. It shouldn't be from either if the side cover gaskets unless the breather is blocked.

Do have a good look at the oil filter. They can be hit by stones or rust through very easily and they are part of the pressurised oil circulation system. From experience, you can have a pinhole in your oil filter that mists oil out only at high revs. That oil can land up anywhere. In my case it was on my right foot and the mainstand.


Good point, oil filter is due to be changed though.

Stink, TUG's description was misleading, the leak is from the main gallery bolt, where oil pressure is tested the bolt is a banjo bolt and is under pressure.
 Back to top
View user's profile Send private message You must be logged in to rate posts

TUG
World Chat Champion



Joined: 12 May 2007
Karma :

PostPosted: 14:36 - 23 Apr 2014    Post subject: Reply with quote

PhilDawson8270 wrote:


Good point, oil filter is due to be changed though.

Stink, TUG's description was misleading, the leak is from the main gallery bolt, where oil pressure is tested the bolt is a banjo bolt and is under pressure.


This, Phil is 100% sure its from the oil pressure testing port/main gallery bolt which makes me believe it is down to the oil pressure relief valve.
____________________
Haz ER-5, innit!
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Mez
Trackday Trickster



Joined: 13 Mar 2004
Karma :

PostPosted: 21:02 - 23 Apr 2014    Post subject: Reply with quote

Wise ones, it turns out it is the water pump. If the seals are so damaged that water is making it to the outside of the bike, should I be doubting the bearing in the pump? I just ask for peoples' past experiences, as I don't have the privilege of being able to leave a job and come back to it. Having the garage 100yds from the house I try to start and finish a job in one go. Fffffff.... Mad
____________________
My deviantArt gallery - My Youtube profile
Honda CG125 -> Baotian BT49 -> AJS JS125 -> Honda CG125-> Kawasaki ZL400 -> Kawasaki GPZ500
 Back to top
View user's profile Send private message Send e-mail Visit poster's website You must be logged in to rate posts

TUG
World Chat Champion



Joined: 12 May 2007
Karma :

PostPosted: 08:18 - 24 Apr 2014    Post subject: Reply with quote

Did you get some pics of the leak?
____________________
Haz ER-5, innit!
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Mez
Trackday Trickster



Joined: 13 Mar 2004
Karma :

PostPosted: 08:59 - 24 Apr 2014    Post subject: Reply with quote

Have done now. On Nokia Potato HD. Hope the upload worked.
____________________
My deviantArt gallery - My Youtube profile
Honda CG125 -> Baotian BT49 -> AJS JS125 -> Honda CG125-> Kawasaki ZL400 -> Kawasaki GPZ500
 Back to top
View user's profile Send private message Send e-mail Visit poster's website You must be logged in to rate posts

TUG
World Chat Champion



Joined: 12 May 2007
Karma :

PostPosted: 09:06 - 24 Apr 2014    Post subject: Reply with quote

Yours is definitely coming from the cover mine is the big bolt to the left of yours.
____________________
Haz ER-5, innit!
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Mez
Trackday Trickster



Joined: 13 Mar 2004
Karma :

PostPosted: 09:19 - 24 Apr 2014    Post subject: Reply with quote

Yarp. Just read through your post while work is quiet. I see the difference.

If I'm changing both seals, the mechanical and the oil, I'll need to drain the oil off won't I? Or should the angle on the sidestand give me enough clearance as it were?
____________________
My deviantArt gallery - My Youtube profile
Honda CG125 -> Baotian BT49 -> AJS JS125 -> Honda CG125-> Kawasaki ZL400 -> Kawasaki GPZ500
 Back to top
View user's profile Send private message Send e-mail Visit poster's website You must be logged in to rate posts

TUG
World Chat Champion



Joined: 12 May 2007
Karma :

PostPosted: 09:24 - 24 Apr 2014    Post subject: Reply with quote

Mez wrote:
Yarp. Just read through your post while work is quiet. I see the difference.

If I'm changing both seals, the mechanical and the oil, I'll need to drain the oil off won't I? Or should the angle on the sidestand give me enough clearance as it were?

Personally? I'd give it fresh fluids all round and tick it off as a service, 2 birds, one stone. Thumbs Up
____________________
Haz ER-5, innit!
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Mez
Trackday Trickster



Joined: 13 Mar 2004
Karma :

PostPosted: 09:47 - 24 Apr 2014    Post subject: Reply with quote

True. Oil filters getting tatty anyways so it'll be due. Thanks folks for all feedback. Hope you get/got sorted Tug Thumbs Up
____________________
My deviantArt gallery - My Youtube profile
Honda CG125 -> Baotian BT49 -> AJS JS125 -> Honda CG125-> Kawasaki ZL400 -> Kawasaki GPZ500
 Back to top
View user's profile Send private message Send e-mail Visit poster's website You must be logged in to rate posts

stinkwheel
Bovine Proctologist



Joined: 12 Jul 2004
Karma :

PostPosted: 12:29 - 24 Apr 2014    Post subject: Reply with quote

Just to warn you. Getting the water pump apart to get at the seals is not easy. It can be well corroded in there.
____________________
“Rule one: Always stick around for one more drink. That's when things happen. That's when you find out everything you want to know.”
I did the 2010 Round Britain Rally on my 350 Bullet. 89 landmarks, 3 months, 9,500 miles.
 Back to top
View user's profile Send private message You must be logged in to rate posts

Mez
Trackday Trickster



Joined: 13 Mar 2004
Karma :

PostPosted: 08:34 - 27 Apr 2014    Post subject: Reply with quote

stinkwheel wrote:
Just to warn you. Getting the water pump apart to get at the seals is not easy. It can be well corroded in there.


I've noticed. Any helpful tips?
____________________
My deviantArt gallery - My Youtube profile
Honda CG125 -> Baotian BT49 -> AJS JS125 -> Honda CG125-> Kawasaki ZL400 -> Kawasaki GPZ500
 Back to top
View user's profile Send private message Send e-mail Visit poster's website You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 207 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.08 Sec - Server Load: 0.95 - MySQL Queries: 15 - Page Size: 102.8 Kb