Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


Head Stock Bearings

Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

FrankGill
Renault 5 Driver



Joined: 18 Jul 2011
Karma :

PostPosted: 17:40 - 24 Apr 2014    Post subject: Head Stock Bearings Reply with quote

I think the head stock bearings on my KLE 500 need changing, is this an easy DIY job or best left to the experts ?
 Back to top
View user's profile Send private message You must be logged in to rate posts

TUG
World Chat Champion



Joined: 12 May 2007
Karma :

PostPosted: 18:10 - 24 Apr 2014    Post subject: Reply with quote

If you haven't done it before, I suggest watching a lot of how to videos. It's a bit of a shit job to do, it's time consuming and you need a grinder/blow torch to remove the old races from the stem.

I need to do mine soon, not looking forward to it either! Laughing
____________________
Haz ER-5, innit!
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

pepperami
Super Spammer



Joined: 17 Jan 2010
Karma :

PostPosted: 19:02 - 24 Apr 2014    Post subject: Reply with quote

It`s not that hard , it`s just a bit of a sod having to pull all the front end off to get at the headstock.

The ball race seats should come off without having to resort to a grinder?, mine always have.
I have always managed to get a little bit of leverage on/under them to push them off the stem.
PlusGas is your friend Thumbs Up as are some thin gash screwdrivers that you no longer want/need that you can use to try and get under the ball-race cup.

I have always found that it`s easier to replace them with taper roller bearings.
On my Superdream it was cheaper to replace with taper roller bearings than it was to replace with original Honda ball-bearings and new cup
____________________
I am the sum total of my own existence, what went before makes me who I am now!
 Back to top
View user's profile Send private message You must be logged in to rate posts

TUG
World Chat Champion



Joined: 12 May 2007
Karma :

PostPosted: 01:30 - 25 Apr 2014    Post subject: Reply with quote

Yea if you have heat at your disposal then it's much easier I don't though so cutting into them until they are weakened then persuading them off is the best option for me Laughing
____________________
Haz ER-5, innit!
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

CaNsA
Super Spammer



Joined: 02 Jan 2008
Karma :

PostPosted: 01:51 - 25 Apr 2014    Post subject: Reply with quote

pepperami wrote:
It's not that hard, it's just a complete ballache


EFA.

Thumbs Up
 Back to top
View user's profile Send private message You must be logged in to rate posts
Vincent This post is not being displayed because the poster is banned. Unhide this post / all posts.

Ariel Badger
Super Spammer



Joined: 02 Dec 2006
Karma :

PostPosted: 20:41 - 25 Apr 2014    Post subject: Reply with quote

If the outer races will not come out run a bead of weld around them, it will contract and they drop out of the frame.
____________________
Bikers make great organ donors, get 115 on your licence today.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

FrankGill
Renault 5 Driver



Joined: 18 Jul 2011
Karma :

PostPosted: 13:37 - 27 Apr 2014    Post subject: Head set bearings Reply with quote

Thanks for your replies. Having read elsewhere now that changing to taper roller bearings that done properly will last a lifetime I thinks I'll get it done at a small bike garage I know.
 Back to top
View user's profile Send private message You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 207 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.05 Sec - Server Load: 0.44 - MySQL Queries: 13 - Page Size: 56.19 Kb