|
|
| Author |
Message |
| Charloam |
This post is not being displayed .
|
 Charloam Two Stroke Sniffer
Joined: 27 Sep 2013 Karma :    
|
 Posted: 11:23 - 28 Apr 2014 Post subject: Puncture! |
 |
|
So I managed to get a slow puncture on my YBR, tubeless tyres.
As far as I can tell from the tyre, there are 2 spots where it looks particularly dodgy, the first image shows a hole which has a stone or something lodged inside it, the second is larger, but I can't make out anything inside it so maybe it hasn't gone all the way through.
I can pump up the tyre, and it stays reasonably inflated for a day or two. So from someone more knowledgeable with motorcycle punctures - is this repairable? Or do I need a new tyre?
I've seen youtube videos of people fixing their punctures with rubber 'strings':
https://www.youtube.com/watch?v=zaa5yIwyxpo
I'm not sure if that will work for me though, since my hole isn't quite so round...
https://i.imgur.com/iFHB9yx.jpg
https://i.imgur.com/qcgzM3m.jpg |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| doggone |
This post is not being displayed .
|
 doggone World Chat Champion

Joined: 20 May 2004 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Scotsman37 |
This post is not being displayed .
|
 Scotsman37 World Chat Champion
Joined: 17 Aug 2004 Karma :  
|
 Posted: 11:31 - 28 Apr 2014 Post subject: |
 |
|
Looks like a new tyre before your next MOT is due!!!!
From pics you've either gone over something like a piece of glass or slither of metal or the other possibility a neighbour doesn't like the sound of your bike at nights and stuck a knife into it?
You could use Tyre Weld till then which will seal the leak from within and re-inflate it for you, then run it for a few miles to heat the tyre up then it sets to seal to it, but you may need to recheck the pressure and pump at bit more air in it to correct pressure!
You can get it at Asda, and sometimes they have it on special offer or you could find it at any other store that stocks it nearby you?
I've went three months one time without having any problems with it after having a nail punctured my rear tyre!
Holts Tyre Weld it's capable re-inflating a car tyre from flat!
p.s. If you do use it as it fully re-inflates the tyre you will see some foamy stuff come out of the hole, and don't worry just wipe of the excess and wipe off the excess. Wait a little as it instructs then ride it for a few miles, recheck tyre pressure and add more air as necessary then you're done!
Sorry you'll no doubt need a new tyre just before next MOT, but at least the quick fix will keep you going for quite sometime until you can afford a replacement!
https://www.holtsauto.com/images/products/repair-and-maintenance/tyre-repair/holts-tyreweld-500ml-hi.jpg
Last edited by Scotsman37 on 11:43 - 28 Apr 2014; edited 1 time in total |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Scotsman37 |
This post is not being displayed .
|
 Scotsman37 World Chat Champion
Joined: 17 Aug 2004 Karma :  
|
 Posted: 11:39 - 28 Apr 2014 Post subject: |
 |
|
This one looks like it's got something stuck in it? Have you tried using long pliers to get in there and pull it out?
https://i.imgur.com/iFHB9yx.jpg |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| stirlinggaz |
This post is not being displayed .
|
 stirlinggaz World Chat Champion

Joined: 22 Jul 2007 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| raesewell |
This post is not being displayed .
|
 raesewell Traffic Copper

Joined: 22 Oct 2012 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Vincent |
This post is not being displayed because the poster is banned. Unhide this post / all posts.
|
 Vincent Banned

Joined: 16 Oct 2006 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Charloam |
This post is not being displayed .
|
 Charloam Two Stroke Sniffer
Joined: 27 Sep 2013 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Scotsman37 |
This post is not being displayed .
|
 Scotsman37 World Chat Champion
Joined: 17 Aug 2004 Karma :  
|
 Posted: 13:22 - 28 Apr 2014 Post subject: |
 |
|
It may not pass the MOT with the current state it is in due to safety?
Sounds good that you're not registering any leaks but those are bad deep cuts, and it is wise of you to remove anything possibly sharp as it may get more pushed in over time....!
MOT checks for tyres and wheels on motorcycles are divided into just two sections. Please click one of the links below to skip to the section of interest.
tyres :: wheels
Tyres
Tyres must be of suitable type and in good repair
Tyres must be seated correctly in their rims
Tyres must be fitted in accordance with direction indicators on the sidewall
All tyres must be either cross ply or radial, not a mixture
Tread must be clearly visible over the whole tread area
Tread must be at least 1mm deep throughout the circumference and 75% of the width of the tyre*
Other reasons for your tyres failing the motorcycle MOT test
It shows a cut longer than 25mm or 10% of the section width of the tyre that reaches the ply or cord
It shows a bulge, lump or tear caused by partial failure of its structure
It fouls another component of the motorcycle
Ply or cord is exposed
The valve is seriously damaged or misaligned
The tread has been recut
https://mot.fasttrackmotorcycles.co.uk/81/motorcycle-mot-checks-tyres-wheels/ |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Charloam |
This post is not being displayed .
|
 Charloam Two Stroke Sniffer
Joined: 27 Sep 2013 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Bunny Lingus |
This post is not being displayed .
|
 Bunny Lingus Traffic Copper

Joined: 20 Apr 2014 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
Old Thread Alert!
The last post was made 12 years, 204 days ago. Instead of replying here, would creating a new thread be more useful? |
 |
|
|