Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


1980's Honda H100 A Voltage problem

Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

AzzA1990
Nova Slayer



Joined: 28 Apr 2014
Karma :

PostPosted: 17:17 - 28 Apr 2014    Post subject: 1980's Honda H100 A Voltage problem Reply with quote

Hi i am new here so first of all let me start of by saying a big hello Very Happy

I have an old 1980's Honda H100 A that i have only just recently brought as a project i got it yesterday and i have got it running today i gave the carb a good clean and put fresh fuel in her and she fired up nicely and sounds sweet!

I am a little concerned about the voltage coming from the bike that's going into the battery it's a 6 volt system however when i put the volt meter on the battery when the engine is started but on idle the volt meter is only reading 4.6 volts? at first i thought it was the battery but now the voltage going into the battery is quite low it has to be something else right?

Now i believe this could be a number of things but i am hoping it's the Regulator/Rectifier so that is why i am on here asking for other peoples opinions

Thanks in advance!
 Back to top
View user's profile Send private message You must be logged in to rate posts

smegballs
World Chat Champion



Joined: 28 Oct 2007
Karma :

PostPosted: 17:51 - 28 Apr 2014    Post subject: Reply with quote

If the battery is old and shagged, it will pull down the voltage the big is trying to feed it hence the low reading. I imagine that the energy for the spark is magneto/cdi then if it runs with such low voltage?

Take the battery out, then put the voltmeter across where the battery would go (assuming the ignition is self generating) this should give you a good idea of what the actual bike is putting out charging voltage wise.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

AzzA1990
Nova Slayer



Joined: 28 Apr 2014
Karma :

PostPosted: 20:18 - 28 Apr 2014    Post subject: Reply with quote

smegballs wrote:
If the battery is old and shagged, it will pull down the voltage the big is trying to feed it hence the low reading. I imagine that the energy for the spark is magneto/cdi then if it runs with such low voltage?

Take the battery out, then put the voltmeter across where the battery would go (assuming the ignition is self generating) this should give you a good idea of what the actual bike is putting out charging voltage wise.


Thanks for the reply

I have just done it without the battery in the bike and it's putting out exactly the same voltage as to when the battery was in the bike

Strange? if it's not the regulator/rectifier then it would be the stator plate and magneto I'm guessing?
 Back to top
View user's profile Send private message You must be logged in to rate posts

smegballs
World Chat Champion



Joined: 28 Oct 2007
Karma :

PostPosted: 20:22 - 28 Apr 2014    Post subject: Reply with quote

Can you post a wiring diagram for the bike?? Being a small 6 volter it probably has some perverse system of tapped lighting/charging coils along with dirty half wave rectification (at least thats what rxs100 has Wink ).

I'll go take a look to and see what I can find. Once I have a diagram I'll be able to suggest a logical test sequence to find the issue.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

AzzA1990
Nova Slayer



Joined: 28 Apr 2014
Karma :

PostPosted: 20:50 - 28 Apr 2014    Post subject: Reply with quote

smegballs wrote:
Can you post a wiring diagram for the bike?? Being a small 6 volter it probably has some perverse system of tapped lighting/charging coils along with dirty half wave rectification (at least thats what rxs100 has Wink ).

I'll go take a look to and see what I can find. Once I have a diagram I'll be able to suggest a logical test sequence to find the issue.


I do have a haynes manual for the bike that has a wiring diagram I'll ry and upload a photo, i am no good when it comes to reading wiring diagrams Confused

I don't think this will be of any help until i get a clearer camera tomorrow but here goes Confused[/img]
 Back to top
View user's profile Send private message You must be logged in to rate posts

A100man
World Chat Champion



Joined: 19 Aug 2013
Karma :

PostPosted: 21:04 - 28 Apr 2014    Post subject: Re: 1980's Honda H100 A Voltage problem Reply with quote

AzzA1990 wrote:
Hi i am new here so first of all let me start of by saying a big hello Very Happy

I have an old 1980's Honda H100 A that i have only just recently brought as a project i got it yesterday and i have got it running today i gave the carb a good clean and put fresh fuel in her and she fired up nicely and sounds sweet!

I am a little concerned about the voltage coming from the bike that's going into the battery it's a 6 volt system however when i put the volt meter on the battery when the engine is started but on idle the volt meter is only reading 4.6 volts? ..


Does it increase when you rev it a bit ?
 Back to top
View user's profile Send private message You must be logged in to rate posts

AzzA1990
Nova Slayer



Joined: 28 Apr 2014
Karma :

PostPosted: 21:11 - 28 Apr 2014    Post subject: Re: 1980's Honda H100 A Voltage problem Reply with quote

A100man wrote:
AzzA1990 wrote:
Hi i am new here so first of all let me start of by saying a big hello Very Happy

I have an old 1980's Honda H100 A that i have only just recently brought as a project i got it yesterday and i have got it running today i gave the carb a good clean and put fresh fuel in her and she fired up nicely and sounds sweet!

I am a little concerned about the voltage coming from the bike that's going into the battery it's a 6 volt system however when i put the volt meter on the battery when the engine is started but on idle the volt meter is only reading 4.6 volts? ..


Does it increase when you rev it a bit ?


It does but not by much i think it went from 4.6v to 4.8 but i was having to rev it quite high
 Back to top
View user's profile Send private message You must be logged in to rate posts

smegballs
World Chat Champion



Joined: 28 Oct 2007
Karma :

PostPosted: 21:28 - 28 Apr 2014    Post subject: Reply with quote

Okay then. Here's the first test. Locate the main connector from the stator to the loom. You might have a two connectors, one for the cdi wires and one for the charging/lighting wires. Or it might all be one connector.


Break the circuit where I've marked in red, and test between the generator side of the yellow and grey wires and ground with the multimeter set onto AC volts. See what the voltage is both at idle and with some revs.

I've drew a little diagram of what is the most likely arrangement inside the lighting/charging coil. One end of the coil is tied to earth, then halfway up the coil it is tapped off for charging purposes. When you turn the lights on, it switches in the rest of the coil to power the lights.

https://i.imgur.com/ZZ87Ttr.png

This test will show whether we are getting enough juice from the stator in the first place, You should probably see at least 10V AC with some revs on.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

AzzA1990
Nova Slayer



Joined: 28 Apr 2014
Karma :

PostPosted: 21:38 - 28 Apr 2014    Post subject: Reply with quote

smegballs wrote:
Okay then. Here's the first test. Locate the main connector from the stator to the loom. You might have a two connectors, one for the cdi wires and one for the charging/lighting wires. Or it might all be one connector.


Break the circuit where I've marked in red, and test between the generator side of the yellow and grey wires and ground with the multimeter set onto AC volts. See what the voltage is both at idle and with some revs.

I've drew a little diagram of what is the most likely arrangement inside the lighting/charging coil. One end of the coil is tied to earth, then halfway up the coil it is tapped off for charging purposes. When you turn the lights on, it switches in the rest of the coil to power the lights.

https://i.imgur.com/ZZ87Ttr.png

This test will show whether we are getting enough juice from the stator in the first place, You should probably see at least 10V AC with some revs on.


Wow thanks a lot you have been a great help i really appreciate it

I will report back tomorrow after trying this! neighbours wouldn't be happy with me if i done it now Laughing
 Back to top
View user's profile Send private message You must be logged in to rate posts

smegballs
World Chat Champion



Joined: 28 Oct 2007
Karma :

PostPosted: 21:54 - 28 Apr 2014    Post subject: Reply with quote

No worries mate, auto-electrics probably my best area of tinkering. I've been teaching myself the electronics knowledge needed to build radio gear from scratch so by comparison auto-electricals are piece of piss!

Once thing to consider is that these 6v systems are marginal at best. The low voltage means that good connections are especially critical than on a 12V machine.

What is your intended outcome from this? These 6V bikes run their ignition system separate to the lights so getting them to run isn't an issue. How is your light output on the headlights? With my rxs, the charging system was shagged with an ancient battery. Despite wild fluctuations on a cold engine (discharged battery, nothing to do with engine warmth), after a few mins riding the battery has absorbed some semblance of charge so the indies flashed sort of acceptably.

The battery on these bikes typically only runs the indies, horn and rear/brake light. You could spend loads of time and money trying to get it to work to the normal standards of a 12V vehicle but IMO if you can get the instrumentation to work reasonable then that is a "win".


Protip: Attach one of those old stylee 6v lantern batteries (disconnect the charging wires) for the MOT and your indies will flash at the proper rate. Wink
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

smegballs
World Chat Champion



Joined: 28 Oct 2007
Karma :

PostPosted: 22:14 - 28 Apr 2014    Post subject: Reply with quote

Another thing I suspect could be a problem is this "resistor" in the lower left corner. I have no idea if it is literally just a resistor or a poorly labelled AC regulator like what the RXS100 has. Either way it's job is clearly to try and limit voltage to keep bulbs blowing.

It occured to me that if it has failed in closed-circuit (or close to), it would present a big load to the stator and pull the voltage right down. Might be an idea to locate it and disconnect that pink wire and measure your voltages again.

If you can, try getting a focussed photo of the bottom of that page when you get access to a camera. It would make it a lot easier to diagnose Thumbs Up

https://i.imgur.com/gmNotx4.png
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

AzzA1990
Nova Slayer



Joined: 28 Apr 2014
Karma :

PostPosted: 14:05 - 30 Apr 2014    Post subject: Reply with quote

Hi sorry it's been a while i tried what you said and i think i must have done it completely wrong because i couldn't get a reading from my multimeter i think the meter it's self is going up the creek too, I am waiting for a new one too arrive, i can confirm though all of the lights work but the indicators are a bit dull and not that bright but they get a bi brighter when i rev the engine obviously, i wanted to put some more modern looking indicators on the bike but i can't find any online that are for 6 volt bike?

I have come across another couple of problems too it's going a bit off topic but there is a very minor crack at the top of the float bowl on the carb it doesn't leak fuel but it could be taking in to much air and also the tube going from the air box to the carb doesn't actually sit over the carb it goes up against it and some numpty has put electrical tape around it to seal it, might explain why the bike want's to die when it's on idle

The idle screw it's as if it's not working very well, it's like problem after problem at the moment
 Back to top
View user's profile Send private message You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 202 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.07 Sec - Server Load: 1.02 - MySQL Queries: 13 - Page Size: 78.66 Kb