Help & FAQs    Search BCF    Members    Groups    Events Calendar
Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


Flywheel Puller (MTX 125)

 Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

Jello
Nova Slayer



Joined: 07 Sep 2008
Karma :
PostPosted: 14:07 - 20 Nov 2008    Post subject: Flywheel Puller (MTX 125) Reply with quote
Well it didn't take long for the bike to get sick again. Bid end bearings this time.

I found another crankshaft on ebay complete with conrod and big end. So I'm in the process of stripping my engine to replace the crankshaft.

I've come unstuck on the flywheel though. The manual suggests using a specific flywheel puller, which I don't have.

Does anybody know of anywhere that would sell such a tool?
____________________
Honda MTX 125
 Back to top
View user's profile Send private message You must be logged in to rate posts

yen_powell
World Chat Champion



Joined: 22 Jun 2008
Karma :
PostPosted: 15:13 - 20 Nov 2008    Post subject: Reply with quote
If it's got a threaded hole in the middle, try using your rear axle. That's worked on a few bikes I've had to remove them from.
____________________
Blackmail is a nasty word........but not as nasty as phlegm!
XT1200Z and a DR350 in bits
 Back to top
View user's profile Send private message You must be logged in to rate posts

sumpgard
Nova Slayer



Joined: 20 Nov 2008
Karma :
PostPosted: 16:11 - 20 Nov 2008    Post subject: Reply with quote
try race spec £5.99 +postage you will have to measure thread +depth required i have just rebuilt my mtx 125 engine i would also make sure you have a manual handy quite complecated when all the gears and selector forks have to be removed to pressout main bearings.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

sumpgard
Nova Slayer



Joined: 20 Nov 2008
Karma :
PostPosted: 16:24 - 20 Nov 2008    Post subject: Reply with quote
try race spec £5.99 +postage you will have to measure thread +depth required i have just rebuilt my mtx 125 engine i would also make sure you have a manual handy quite complecated when all the gears and selector forks have to be removed to pressout main bearings.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Jello
Nova Slayer



Joined: 07 Sep 2008
Karma :
PostPosted: 02:45 - 23 Nov 2008    Post subject: Reply with quote
yen_powell wrote:
If it's got a threaded hole in the middle, try using your rear axle. That's worked on a few bikes I've had to remove them from.

Sorry, I don't follow...
____________________
Honda MTX 125
 Back to top
View user's profile Send private message You must be logged in to rate posts

yen_powell
World Chat Champion



Joined: 22 Jun 2008
Karma :
PostPosted: 10:37 - 23 Nov 2008    Post subject: Reply with quote
Jello wrote:
yen_powell wrote:
If it's got a threaded hole in the middle, try using your rear axle. That's worked on a few bikes I've had to remove them from.

Sorry, I don't follow...
If the flywheel is sitting on a tapered shaft and has a threaded hole in the centre then a flywheel puller screws into the hole and when it touches the end of the tapered shaft, you carry on turning it (it gets harder) and it forces the flywheel off of the shaft.

It sometimes occurs that the thread on the rear axle is the same thread on the flywheel. I've used the rear axle a couple of times (on a Yam XT125, is the only one I can definitely remember) and it's worked.
____________________
Blackmail is a nasty word........but not as nasty as phlegm!
XT1200Z and a DR350 in bits
 Back to top
View user's profile Send private message You must be logged in to rate posts

frazer1981
Nitrous Nuisance



Joined: 04 Oct 2008
Karma :
PostPosted: 12:09 - 23 Nov 2008    Post subject: Reply with quote
i got a draper 3 arm puller to get my one off the shaft. Think it cost me a fiver from local car shop. The only thing though is i had to reprofile the arms to fit in the holes in the fly wheel. I have not took it off yet as i don't want to freeze my ****** off in the garage at the minute Razz
____________________
1st bike - chunlan starway 50QF4 (SOLD) 2nd bike - 92 Honda mtx125RW-L ( In my garage awaiting some TLC)
05 Honda xl125v Varadero stolen and recovered but now a write off! Sad
07 Hyosung GTR125R
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
Old Thread Alert!

The last post was made 17 years, 319 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT + 1 Hour
Page 1 of 1

 
 You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 
Debug Mode: ON - Server: birks (www) - Page Generation Time: 0.07 Sec - Server Load: 0.81 - MySQL Queries: 14 - Page Size: 52.42 Kb