Help & FAQs    Search BCF    Members    Groups    Events Calendar
Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


CBR 6 minor changes.

 Reply to topic
Bike Chat Forums Index -> Show & Tell
View previous topic : View next topic  
Author Message

Ichy
World Chat Champion



Joined: 15 Jul 2005
Karma :
PostPosted: 21:35 - 11 Mar 2011    Post subject: CBR 6 minor changes. Reply with quote
I've been busy over the last few months doing stuff, none of it to my CBR. A number of parts have been sitting around waiting to be fitted so I thought it time to start.
https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/DSCF6811.jpg

First bit was the hanger. I rarely, if ever take pillions on the CBR so I wanted it to be as close to solo as possible. It took a bit of time to find one that wasn't massively overpriced but this one from laser turned up. It was so cheap I brought two!
https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/DSCF6814.jpg

So this is how it looks as standard.
https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/DSCF6812.jpg
https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/DSCF6813.jpg

Pretty easy to fit, release rear cowl and just slide it back a bit to give access to the hanger bolts. Slightly awkward due to the undertray. No real point in photos of how I did it, very basic stuff really but I am happy with the final look.
https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/DSCF6817.jpg
https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/DSCF6820.jpg
https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/DSCF6821.jpg

Next bit is likely to be the main crash bungs. I've got to drill through the fairing to fit them. Could be interesting, I've never done it before. I would prefer to do it without removing the fairing but we will see.
____________________
https://www.metacafe.com/watch/1972097/how_to_behave_on_a_forum/
 Back to top
View user's profile Send private message You must be logged in to rate posts

Ichy
World Chat Champion



Joined: 15 Jul 2005
Karma :
PostPosted: 21:36 - 13 Mar 2011    Post subject: Reply with quote
Bit more done.
Very little worth mentioning about the front spindle sliders. 5 minutes to fit if that.
https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/frontspindle.jpg

Even being careful its hard to get the center of the engine bolt exactly. Started with a 3mm drill, 10mm next, then 16mm and finally 25mm. I used a cone drill to make the hole, easy to control and it looks tidy.
https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/bighole.jpg

Motrax mushrooms left on for comparison.
https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/bung1.jpg

https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/bung2.jpg

Looks good to me. A significant improvement looks wise to the motrax ones. Having sat down and thought about it I may open up the hole in the fairing to allow for the bung to bend should the worst happen.
____________________
https://www.metacafe.com/watch/1972097/how_to_behave_on_a_forum/
 Back to top
View user's profile Send private message You must be logged in to rate posts

CHR15
Turbo nutter bastard



Joined: 14 Jun 2008
Karma :
PostPosted: 21:45 - 13 Mar 2011    Post subject: Reply with quote
how are the front spindle sliders held in?
____________________
Turbocharged drag thing / project death weapon / GK73A
Ste: I'm not entirely sure how you'd go about verbally abusing someone with a potato but I'm sure it's possible.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

lllN30lll
World Chat Champion



Joined: 12 Jun 2005
Karma :
PostPosted: 21:48 - 13 Mar 2011    Post subject: Reply with quote
CHR15 wrote:
how are the front spindle sliders held in?

bar through the front spindle, then lock nutted into place.
 Back to top
View user's profile Send private message You must be logged in to rate posts

CHR15
Turbo nutter bastard



Joined: 14 Jun 2008
Karma :
PostPosted: 21:53 - 13 Mar 2011    Post subject: Reply with quote
ahh, thats nice and simple.

*off to browse ebay for skateboard wheels* Mr. Green
____________________
Turbocharged drag thing / project death weapon / GK73A
Ste: I'm not entirely sure how you'd go about verbally abusing someone with a potato but I'm sure it's possible.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Ichy
World Chat Champion



Joined: 15 Jul 2005
Karma :
PostPosted: 21:53 - 13 Mar 2011    Post subject: Reply with quote
CHR15 wrote:
how are the front spindle sliders held in?


They come with a drilled out spindle bolt and the spindle is already hollow.
____________________
https://www.metacafe.com/watch/1972097/how_to_behave_on_a_forum/
 Back to top
View user's profile Send private message You must be logged in to rate posts

Ichy
World Chat Champion



Joined: 15 Jul 2005
Karma :
PostPosted: 21:57 - 13 Mar 2011    Post subject: Reply with quote
CHR15 wrote:
ahh, thats nice and simple.

*off to browse ebay for skateboard wheels* Mr. Green


That is exactly what I was going to do originally, then I decided I'd turn some up myself. I eventually brought these for £17. If you look at the biketek sliders in the first picture I paid about £4 for them with postage. It'll be interesting mounting those to the swingarm.
____________________
https://www.metacafe.com/watch/1972097/how_to_behave_on_a_forum/
 Back to top
View user's profile Send private message You must be logged in to rate posts

mad4it028
World Chat Champion



Joined: 04 Jul 2006
Karma :
PostPosted: 01:03 - 14 Mar 2011    Post subject: Reply with quote
dont use skateboard wheels they dont slide and instead grip into the road and flip the bike causing even more damage,as i buy crash damaged bikes i have seen the result many times
____________________
always looking to buy bikes crashed ,unfinished projects,none runners pm me
currently riding kawasaki z1000 only bike ive ever loved
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

CHR15
Turbo nutter bastard



Joined: 14 Jun 2008
Karma :
PostPosted: 08:36 - 14 Mar 2011    Post subject: Reply with quote
ahh. fair enough Thumbs Up
____________________
Turbocharged drag thing / project death weapon / GK73A
Ste: I'm not entirely sure how you'd go about verbally abusing someone with a potato but I'm sure it's possible.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

DrDonnyBrago
World Chat Champion



Joined: 03 Jan 2010
Karma :
PostPosted: 11:59 - 14 Mar 2011    Post subject: Reply with quote
Do you have a link for the Laser exhaust hangers?

Looking good though mate, how do you plan on attaching the swingarm spools?
 Back to top
View user's profile Send private message You must be logged in to rate posts

Ichy
World Chat Champion



Joined: 15 Jul 2005
Karma :
PostPosted: 13:16 - 14 Mar 2011    Post subject: Reply with quote
DonnyBrago wrote:
Do you have a link for the Laser exhaust hangers?

Looking good though mate, how do you plan on attaching the swingarm spools?


The hangers were a one off find on Ebay. I'd been searching for some time for a decent priced hanger, there was no way that I would pay £50 for a R&G. The seller listed two but didn't describe them very well. Finish isn't brilliant on them but they cost significately less than expected so I'm pretty happy. If you know someone with a welder then it would be easy enough to knock one up.

The swingarm spools are a bit of an unknown. I have two options. I could go through the spindle, the same as the front. My concern is that they will hit the exhaust. The second option is to weld a tapped tube on to the underside of each side of the swingarm. This does mean that it will all need to be stripped but it also means that I will be able to get the swingarm powdercoated, probably black. Dunno. I shall think about it.
____________________
https://www.metacafe.com/watch/1972097/how_to_behave_on_a_forum/
 Back to top
View user's profile Send private message You must be logged in to rate posts

DrDonnyBrago
World Chat Champion



Joined: 03 Jan 2010
Karma :
PostPosted: 14:39 - 14 Mar 2011    Post subject: Reply with quote
Marki wrote:
The swingarm spools are a bit of an unknown. I have two options. I could go through the spindle, the same as the front. My concern is that they will hit the exhaust. The second option is to weld a tapped tube on to the underside of each side of the swingarm. This does mean that it will all need to be stripped but it also means that I will be able to get the swingarm powdercoated, probably black. Dunno. I shall think about it.


Last time I had a look at mine, the rear axle spindle wasn't perfectly hollow the whole way through, there is a restriction of the internal diameter near the RHS. Might be that you could slide a piece of bar into the spindle with a thread tapped into each end and then use a long bolt to reach in through the narrow part on the RHS.


EDIT: Found a link

https://cbrforum.com/forum/showthread.php?t=54650

Can't be good for the unsprung weight though Thumbs Down .
 Back to top
View user's profile Send private message You must be logged in to rate posts

Ichy
World Chat Champion



Joined: 15 Jul 2005
Karma :
PostPosted: 19:18 - 14 Mar 2011    Post subject: Reply with quote
DonnyBrago wrote:

Can't be good for the unsprung weight though Thumbs Down .


Personally I don't think it will make any noticeable difference on a road bike.
____________________
https://www.metacafe.com/watch/1972097/how_to_behave_on_a_forum/
 Back to top
View user's profile Send private message You must be logged in to rate posts

Ichy
World Chat Champion



Joined: 15 Jul 2005
Karma :
PostPosted: 20:18 - 17 Mar 2011    Post subject: Reply with quote
DonnyBrago wrote:


Last time I had a look at mine, the rear axle spindle wasn't perfectly hollow the whole way through, there is a restriction of the internal diameter near the RHS.


I went for 8mm allthread for starters, fitted straight through the spindle.
https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/rearbung1.jpg

Not altogether sold on the idea. I'm a little concerned over the clearance to the end can.

https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/rearbung2.jpg


I think that it may be a better idea to drill the swingarm and fit rivnuts.
____________________
https://www.metacafe.com/watch/1972097/how_to_behave_on_a_forum/
 Back to top
View user's profile Send private message You must be logged in to rate posts

DrDonnyBrago
World Chat Champion



Joined: 03 Jan 2010
Karma :
PostPosted: 08:29 - 18 Mar 2011    Post subject: Reply with quote
Might be right there mate.

Assuming the rear end of yours is the same as mine then the rear wheel has 119mm of travel, could be worth getting it on the centre stand to unload the rear wheel and having a play with a tape measure.
 Back to top
View user's profile Send private message You must be logged in to rate posts

Ichy
World Chat Champion



Joined: 15 Jul 2005
Karma :
PostPosted: 12:26 - 18 Mar 2011    Post subject: Reply with quote
Not a bad idea, I don't have a stand but I do have a hoist.
____________________
https://www.metacafe.com/watch/1972097/how_to_behave_on_a_forum/
 Back to top
View user's profile Send private message You must be logged in to rate posts

Ichy
World Chat Champion



Joined: 15 Jul 2005
Karma :
PostPosted: 20:45 - 19 Mar 2011    Post subject: Reply with quote
No biggie. Some time ago Chr15 gave me some carbon look foil. I wrapped some around the cannister for the rear suspension. I like it.

https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/cannister.jpg

https://i93.photobucket.com/albums/l41/marki_03/stuff/cbr/DSCF6870.jpg

The heel plate is actually carbon. The pattern on the foil is pretty good.

Just order new Hel brake lines. Bloke here www.helmobile.com is doing full stainless for £58 plus postage if you use the code FORUM.
Clear indys and an exhaust protector on their way.
____________________
https://www.metacafe.com/watch/1972097/how_to_behave_on_a_forum/
 Back to top
View user's profile Send private message You must be logged in to rate posts

DrDonnyBrago
World Chat Champion



Joined: 03 Jan 2010
Karma :
PostPosted: 10:32 - 22 Mar 2011    Post subject: Reply with quote
I just put Hel lines on mine, I paid £59 though so now feel a little cheated out of my £1. For the canister, I use a red bull can:

https://i1015.photobucket.com/albums/af271/DonnyBrago/Redbulllovin.jpg
 Back to top
View user's profile Send private message You must be logged in to rate posts

Ichy
World Chat Champion



Joined: 15 Jul 2005
Karma :
PostPosted: 13:07 - 22 Mar 2011    Post subject: Reply with quote
Where did you have the brake lines from? I couldn't find anything anywhere near the price in stainless. Goodridge were close but that was for zinc ends.
____________________
https://www.metacafe.com/watch/1972097/how_to_behave_on_a_forum/
 Back to top
View user's profile Send private message You must be logged in to rate posts

DrDonnyBrago
World Chat Champion



Joined: 03 Jan 2010
Karma :
PostPosted: 14:16 - 22 Mar 2011    Post subject: Reply with quote
Marki wrote:
Where did you have the brake lines from? I couldn't find anything anywhere near the price in stainless. Goodridge were close but that was for zinc ends.


My brother (bacon on here) is a member of MCNninjas forum, there is a guy on there that works for/owns https://www.intobikes.co.uk/ and offers an MCN ninjas forum discount.

I got the carbolook (smoked black) hoses and st/st ends - 2F 1R setup. Is the £58 for all three lines?
 Back to top
View user's profile Send private message You must be logged in to rate posts

Ichy
World Chat Champion



Joined: 15 Jul 2005
Karma :
PostPosted: 16:06 - 22 Mar 2011    Post subject: Reply with quote
Yes for all three. I went for yellow lines with black ends. No imagination.
____________________
https://www.metacafe.com/watch/1972097/how_to_behave_on_a_forum/
 Back to top
View user's profile Send private message You must be logged in to rate posts

AL-
World Chat Champion



Joined: 17 Mar 2005
Karma :
PostPosted: 10:32 - 23 Mar 2011    Post subject: Reply with quote
Love the yellow CBR's Drooling
 Back to top
View user's profile Send private message You must be logged in to rate posts
Old Thread Alert!

The last post was made 14 years, 60 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> Show & Tell All times are GMT
Page 1 of 1

 
 You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 
Debug Mode: ON - Server: birks (www) - Page Generation Time: 0.11 Sec - Server Load: 0.64 - MySQL Queries: 14 - Page Size: 122.17 Kb