|
|
| Author |
Message |
| FrankGill |
This post is not being displayed .
|
 FrankGill Renault 5 Driver
Joined: 18 Jul 2011 Karma :     
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| TUG |
This post is not being displayed .
|
 TUG World Chat Champion
Joined: 12 May 2007 Karma :  
|
 Posted: 18:10 - 24 Apr 2014 Post subject: |
 |
|
If you haven't done it before, I suggest watching a lot of how to videos. It's a bit of a shit job to do, it's time consuming and you need a grinder/blow torch to remove the old races from the stem.
I need to do mine soon, not looking forward to it either!  ____________________ Haz ER-5, innit! |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| pepperami |
This post is not being displayed .
|
 pepperami Super Spammer

Joined: 17 Jan 2010 Karma :    
|
 Posted: 19:02 - 24 Apr 2014 Post subject: |
 |
|
It`s not that hard , it`s just a bit of a sod having to pull all the front end off to get at the headstock.
The ball race seats should come off without having to resort to a grinder?, mine always have.
I have always managed to get a little bit of leverage on/under them to push them off the stem.
PlusGas is your friend as are some thin gash screwdrivers that you no longer want/need that you can use to try and get under the ball-race cup.
I have always found that it`s easier to replace them with taper roller bearings.
On my Superdream it was cheaper to replace with taper roller bearings than it was to replace with original Honda ball-bearings and new cup ____________________ I am the sum total of my own existence, what went before makes me who I am now! |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| TUG |
This post is not being displayed .
|
 TUG World Chat Champion
Joined: 12 May 2007 Karma :  
|
 Posted: 01:30 - 25 Apr 2014 Post subject: |
 |
|
Yea if you have heat at your disposal then it's much easier I don't though so cutting into them until they are weakened then persuading them off is the best option for me  ____________________ Haz ER-5, innit! |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| CaNsA |
This post is not being displayed .
|
 CaNsA Super Spammer

Joined: 02 Jan 2008 Karma :   
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Vincent |
This post is not being displayed because the poster is banned. Unhide this post / all posts.
|
 Vincent Banned

Joined: 16 Oct 2006 Karma :    
|
 Posted: 11:22 - 25 Apr 2014 Post subject: |
 |
|
it's not a difficult job technically....it's just that the lower race can be a bitch to remove sometimes. It sits into a step and it's hard to get anything on it to hammer it out. If you have a good selection of tools, and some patience, you should be alright. There is a proper tool for the bottom race, used more on trials bikes. I've never used one myself but often thought about buying one. It's usually worth converting to Taper Roller bearings if not done already and don't forget to re-tighten after a few miles.
www.ebay.co.uk/itm/35mm-55mm-Motorcycle-Steering-Head-Bearing-Drift-Removal-Tool-/141166962210 ____________________ Space Is Deep |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Ariel Badger |
This post is not being displayed .
|
 Ariel Badger Super Spammer

Joined: 02 Dec 2006 Karma :     
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| FrankGill |
This post is not being displayed .
|
 FrankGill Renault 5 Driver
Joined: 18 Jul 2011 Karma :     
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
Old Thread Alert!
The last post was made 12 years, 207 days ago. Instead of replying here, would creating a new thread be more useful? |
 |
|
|