|
|
| Author |
Message |
| DrSnoosnoo |
This post is not being displayed .
|
 DrSnoosnoo World Chat Champion

Joined: 28 Mar 2012 Karma :   
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| mentalboy |
This post is not being displayed .
|
 mentalboy World Chat Champion

Joined: 05 May 2012 Karma :   
|
 Posted: 20:57 - 22 Apr 2014 Post subject: |
 |
|
Assuming you mean the nice bright squarish bit (sorry haven't got the foggiest what that is ) that is clamping in the right side of your camshafts?
If so, it's probably a good interference fit and will PROBABLY require a light tap with a rubber mallet to free it (Alternatively try rotating the camshafts) ____________________ Make mine a Corona. |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| DrSnoosnoo |
This post is not being displayed .
|
 DrSnoosnoo World Chat Champion

Joined: 28 Mar 2012 Karma :   
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| mentalboy |
This post is not being displayed .
|
 mentalboy World Chat Champion

Joined: 05 May 2012 Karma :   
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Pete. |
This post is not being displayed .
|
 Pete. Super Spammer

Joined: 22 Aug 2006 Karma :     
|
 Posted: 21:39 - 22 Apr 2014 Post subject: |
 |
|
I'd run those cam cap bolts down to just one turn out and use a plastic hammer. When it pops up against the bolts undo them all in sequence one turn at a time to let the cover rise evenly. It's easy to break those things, though that one looks quite strong. ____________________ a.k.a 'Geri'
132.9mph off and walked away. Gear is good, gear is good, gear is very very good  |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| WD Forte |
This post is not being displayed .
|
 WD Forte World Chat Champion

Joined: 17 Jun 2010 Karma :   
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| DrSnoosnoo |
This post is not being displayed .
|
 DrSnoosnoo World Chat Champion

Joined: 28 Mar 2012 Karma :   
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| DrSnoosnoo |
This post is not being displayed .
|
 DrSnoosnoo World Chat Champion

Joined: 28 Mar 2012 Karma :   
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| stinkwheel |
This post is not being displayed .
|
 stinkwheel Bovine Proctologist

Joined: 12 Jul 2004 Karma :    
|
 Posted: 10:11 - 23 Apr 2014 Post subject: |
 |
|
As Pete says, you want to do that gradually because cam caps can snap and if they do, your head is scrap (the hole for the cam is through-bored with the cam cap in place, they are all slightly different).
I generally undo all the bolts one turn at a time working with diagonal opposites like you would with a cylinder head, then gently tap round the cam cap with a deadblow hammer or a piece of wood so it's resting up against the bolts. Rinse and repeat until it's free to move.
Put them back on the same way, little by little and diagonal opposites so they go down square. There is probably a tightening order in the workshop manual. I usually torque them down in two or three stages once they are all the way down.
Also make sure the cam lobes are facing away from the valves so the valvce springs aren't popping the cams up. ____________________ “Rule one: Always stick around for one more drink. That's when things happen. That's when you find out everything you want to know.”
I did the 2010 Round Britain Rally on my 350 Bullet. 89 landmarks, 3 months, 9,500 miles. |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| DrSnoosnoo |
This post is not being displayed .
|
 DrSnoosnoo World Chat Champion

Joined: 28 Mar 2012 Karma :   
|
 Posted: 10:17 - 23 Apr 2014 Post subject: |
 |
|
| stinkwheel wrote: | As Pete says, you want to do that gradually because cam caps can snap and if they do, your head is scrap (the hole for the cam is through-bored with the cam cap in place, they are all slightly different).
I generally undo all the bolts one turn at a time working with diagonal opposites like you would with a cylinder head, then gently tap round the cam cap with a deadblow hammer or a piece of wood so it's resting up against the bolts. Rinse and repeat until it's free to move.
Put them back on the same way, little by little and diagonal opposites so they go down square. There is probably a tightening order in the workshop manual. I usually torque them down in two or three stages once they are all the way down.
Also make sure the cam lobes are facing away from the valves so the valvce springs aren't popping the cams up. |
I did undo them bit by bit but I probably should have been knocking them to sit up with the bolt. I followed the order that's embossed over the covers, they're numbered 1 - 16 so I undid 16 to 1. I'll cut my losses, put it all back on and untighten again trying to raise it as I loosen it all up.
As for the Cam lobes, the manual told me to make it TDC so I did that.
I hope my head isn't scrap!!! Don't scare me like this! ____________________ I'm Sam; Northern, Ginger, Lover
Did have: '95 ZZR600 '83 CG125 '97 ZZR1100 '15 Hypermotard 821 SP Do Have: '10 ZX10R |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| DrSnoosnoo |
This post is not being displayed .
|
 DrSnoosnoo World Chat Champion

Joined: 28 Mar 2012 Karma :   
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| stinkwheel |
This post is not being displayed .
|
 stinkwheel Bovine Proctologist

Joined: 12 Jul 2004 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| DrSnoosnoo |
This post is not being displayed .
|
 DrSnoosnoo World Chat Champion

Joined: 28 Mar 2012 Karma :   
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| mentalboy |
This post is not being displayed .
|
 mentalboy World Chat Champion

Joined: 05 May 2012 Karma :   
|
 Posted: 18:33 - 23 Apr 2014 Post subject: |
 |
|
Take an old wire coat hanger. Open it out and thread it under the chain between the cams so it supports the chain across the length of the head, also stuff some clean rag down the cam chain shaft so that if you drop anything you won't be wondering how to fish it out of the depths!
Take a look at the markings on the cam chain sprockets. Observe how they are lined up - You may need to put a small something in the adjuster hole to take up the slack in the chain. Theoretically there should be a marking on each sprocket that is in line with the cylinder head - if the lower end is still in the correct position. You shouldn't need any marker pens etc  ____________________ Make mine a Corona. |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| DrSnoosnoo |
This post is not being displayed .
|
 DrSnoosnoo World Chat Champion

Joined: 28 Mar 2012 Karma :   
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| mentalboy |
This post is not being displayed .
|
 mentalboy World Chat Champion

Joined: 05 May 2012 Karma :   
|
 Posted: 20:53 - 23 Apr 2014 Post subject: |
 |
|
Firstly I hope that you weren't describing your hammer action literally!!!
Have you already ordered the shims? I had the same situation as you fairly recently and discovered purely by chance that it was more economically sound to buy a 'trade' pack of shims (obviously making sure you get the right diameter!!).I think there were about ninety in a box for about £70 which worked out cheaper than the 12 OEM's that I'd been quoted for and gave me a huge amount of options for chopping and changing shims as necessary.
Also gives you somewhere handy to store old shims - don't throw them away as you'll never know when they'll come in handy! ____________________ Make mine a Corona. |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| DrSnoosnoo |
This post is not being displayed .
|
 DrSnoosnoo World Chat Champion

Joined: 28 Mar 2012 Karma :   
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Vincent |
This post is not being displayed because the poster is banned. Unhide this post / all posts.
|
 Vincent Banned

Joined: 16 Oct 2006 Karma :    
|
 Posted: 13:22 - 24 Apr 2014 Post subject: |
 |
|
They look like pair valves, you're bike Fi? If they are....you don't need em 'Suspicious why one is oilier........worn valve seal maybe?
You're brave if you've never done valve clearances before......my advice would be to check everything three times......and keep your oil ways clean.  ____________________ Space Is Deep |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| DrSnoosnoo |
This post is not being displayed .
|
 DrSnoosnoo World Chat Champion

Joined: 28 Mar 2012 Karma :   
|
 Posted: 10:16 - 26 Apr 2014 Post subject: |
 |
|
| Vincent wrote: |
They look like pair valves, you're bike Fi? If they are....you don't need em 'Suspicious why one is oilier........worn valve seal maybe?
You're brave if you've never done valve clearances before......my advice would be to check everything three times......and keep your oil ways clean.  |
Nope it's a carby! Yeah I'm brave but also tight, I don't wanna pay hundreds on this bike that isn't worth much anymore.
The way I see it, if I can get to my final year of a PhD, I can follow some Haynes manuals with the right tools and the internet. ____________________ I'm Sam; Northern, Ginger, Lover
Did have: '95 ZZR600 '83 CG125 '97 ZZR1100 '15 Hypermotard 821 SP Do Have: '10 ZX10R |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
Old Thread Alert!
The last post was made 12 years, 208 days ago. Instead of replying here, would creating a new thread be more useful? |
 |
|
|