Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


How to get this part off?

Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

DrSnoosnoo
World Chat Champion



Joined: 28 Mar 2012
Karma :

PostPosted: 20:52 - 22 Apr 2014    Post subject: How to get this part off? Reply with quote

So I'm doing the valve clearances on the zzr600, very scary but I'm armed with the Haynes book of lies. Now I've got this stuck on my camshafts, see attached picture, How do I get it off? I undid the screws in order.

Should I try putting the other side back on and see if I can get it off then?
____________________
I'm Sam; Northern, Ginger, Lover
Did have: '95 ZZR600 '83 CG125 '97 ZZR1100 '15 Hypermotard 821 SP Do Have: '10 ZX10R
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

mentalboy
World Chat Champion



Joined: 05 May 2012
Karma :

PostPosted: 20:57 - 22 Apr 2014    Post subject: Reply with quote

Assuming you mean the nice bright squarish bit (sorry haven't got the foggiest what that is Wink ) that is clamping in the right side of your camshafts?
If so, it's probably a good interference fit and will PROBABLY require a light tap with a rubber mallet to free it (Alternatively try rotating the camshafts)
____________________
Make mine a Corona.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

DrSnoosnoo
World Chat Champion



Joined: 28 Mar 2012
Karma :

PostPosted: 20:58 - 22 Apr 2014    Post subject: Reply with quote

mentalboy wrote:
Assuming you mean the nice bright squarish bit (sorry haven't got the foggiest what that is Wink ) that is clamping in the right side of your camshafts?
If so, it's probably a good interference fit and will PROBABLY require a light tap with a rubber mallet to free it (Alternatively try rotating the camshafts)


Yeah the squarish bit I can't remember what Mr Haynes calls it. The cam chain tensioner is out now and that books says not to rotate it now or stuff might get damaged, correct me if I'm wrong though.
____________________
I'm Sam; Northern, Ginger, Lover
Did have: '95 ZZR600 '83 CG125 '97 ZZR1100 '15 Hypermotard 821 SP Do Have: '10 ZX10R
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

mentalboy
World Chat Champion



Joined: 05 May 2012
Karma :

PostPosted: 21:18 - 22 Apr 2014    Post subject: Reply with quote

Another trick for freeing the camshaft and it's restraining bits and bobs would be to apply steady downward pressure on top of the camchain (between the two shafts) whilst keeping your hand on the left side to prevent it jumping out from that end.
The slight pressure should be enough to slightly move the camshaft and pop the 'thingy' on the right.
Personally I'd just be twatting it LIGHTLY' with my rubber mallet by now
____________________
Make mine a Corona.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Pete.
Super Spammer



Joined: 22 Aug 2006
Karma :

PostPosted: 21:39 - 22 Apr 2014    Post subject: Reply with quote

I'd run those cam cap bolts down to just one turn out and use a plastic hammer. When it pops up against the bolts undo them all in sequence one turn at a time to let the cover rise evenly. It's easy to break those things, though that one looks quite strong.
____________________
a.k.a 'Geri'

132.9mph off and walked away. Gear is good, gear is good, gear is very very good Very Happy
 Back to top
View user's profile Send private message Visit poster's website You must be logged in to rate posts

WD Forte
World Chat Champion



Joined: 17 Jun 2010
Karma :

PostPosted: 22:32 - 22 Apr 2014    Post subject: Reply with quote

Isnt it a bearing holder?
( with bit of added manifold thrown in)
I'd be trying some cautious levering/rocking to break it free

That bottom LH cam shaft looks a bit odd and reddish
and it all looks bit dry too
has it been laid up?
____________________
bikers smell of wee
 Back to top
View user's profile Send private message You must be logged in to rate posts

DrSnoosnoo
World Chat Champion



Joined: 28 Mar 2012
Karma :

PostPosted: 08:58 - 23 Apr 2014    Post subject: Reply with quote

Pete. wrote:
I'd run those cam cap bolts down to just one turn out and use a plastic hammer. When it pops up against the bolts undo them all in sequence one turn at a time to let the cover rise evenly. It's easy to break those things, though that one looks quite strong.


Thanks Pete, so I should just tighten down that side or shall I put the other side on and screw them all in again?

These seem quote tough, quite thick metal.

I've given it a good pull and it's not budging so I'll have to try again tonight when I've finished work.

WD Forte wrote:
Isnt it a bearing holder?
( with bit of added manifold thrown in)
I'd be trying some cautious levering/rocking to break it free

That bottom LH cam shaft looks a bit odd and reddish
and it all looks bit dry too
has it been laid up?


The one at the bottom is the IN cam it does look all that colour while the EX has a slight green colour to it, is it for distinguishing? I'm gonna get the verniers on them when they're out to check them over while I'm in there, don't wanna be doing all this again in a hurry!

It's not dry there is a good covering of oil over everything.

Thanks for the help so far gang. I've been taking hundreds of pictures so will hopefully write it up when I'm done to help other Valve clearance virigns.
____________________
I'm Sam; Northern, Ginger, Lover
Did have: '95 ZZR600 '83 CG125 '97 ZZR1100 '15 Hypermotard 821 SP Do Have: '10 ZX10R
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

DrSnoosnoo
World Chat Champion



Joined: 28 Mar 2012
Karma :

PostPosted: 09:12 - 23 Apr 2014    Post subject: Reply with quote

Also, looking at these, valves, one side is covered in muck while the other is ok. What are these? The exhaust valves on 1 and 2 are too tight while 3 and 4 are fine.

https://scontent-b-lhr.xx.fbcdn.net/hphotos-frc3/t1.0-9/10308302_10154032987265258_4002090570810439075_n.jpg
____________________
I'm Sam; Northern, Ginger, Lover
Did have: '95 ZZR600 '83 CG125 '97 ZZR1100 '15 Hypermotard 821 SP Do Have: '10 ZX10R
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

stinkwheel
Bovine Proctologist



Joined: 12 Jul 2004
Karma :

PostPosted: 10:11 - 23 Apr 2014    Post subject: Reply with quote

As Pete says, you want to do that gradually because cam caps can snap and if they do, your head is scrap (the hole for the cam is through-bored with the cam cap in place, they are all slightly different).

I generally undo all the bolts one turn at a time working with diagonal opposites like you would with a cylinder head, then gently tap round the cam cap with a deadblow hammer or a piece of wood so it's resting up against the bolts. Rinse and repeat until it's free to move.

Put them back on the same way, little by little and diagonal opposites so they go down square. There is probably a tightening order in the workshop manual. I usually torque them down in two or three stages once they are all the way down.

Also make sure the cam lobes are facing away from the valves so the valvce springs aren't popping the cams up.
____________________
“Rule one: Always stick around for one more drink. That's when things happen. That's when you find out everything you want to know.”
I did the 2010 Round Britain Rally on my 350 Bullet. 89 landmarks, 3 months, 9,500 miles.
 Back to top
View user's profile Send private message You must be logged in to rate posts

DrSnoosnoo
World Chat Champion



Joined: 28 Mar 2012
Karma :

PostPosted: 10:17 - 23 Apr 2014    Post subject: Reply with quote

stinkwheel wrote:
As Pete says, you want to do that gradually because cam caps can snap and if they do, your head is scrap (the hole for the cam is through-bored with the cam cap in place, they are all slightly different).

I generally undo all the bolts one turn at a time working with diagonal opposites like you would with a cylinder head, then gently tap round the cam cap with a deadblow hammer or a piece of wood so it's resting up against the bolts. Rinse and repeat until it's free to move.

Put them back on the same way, little by little and diagonal opposites so they go down square. There is probably a tightening order in the workshop manual. I usually torque them down in two or three stages once they are all the way down.

Also make sure the cam lobes are facing away from the valves so the valvce springs aren't popping the cams up.


I did undo them bit by bit but I probably should have been knocking them to sit up with the bolt. I followed the order that's embossed over the covers, they're numbered 1 - 16 so I undid 16 to 1. I'll cut my losses, put it all back on and untighten again trying to raise it as I loosen it all up.

As for the Cam lobes, the manual told me to make it TDC so I did that.

I hope my head isn't scrap!!! Don't scare me like this!
____________________
I'm Sam; Northern, Ginger, Lover
Did have: '95 ZZR600 '83 CG125 '97 ZZR1100 '15 Hypermotard 821 SP Do Have: '10 ZX10R
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

DrSnoosnoo
World Chat Champion



Joined: 28 Mar 2012
Karma :

PostPosted: 10:19 - 23 Apr 2014    Post subject: Reply with quote

Double post, having some weird errors form bcf today!
____________________
I'm Sam; Northern, Ginger, Lover
Did have: '95 ZZR600 '83 CG125 '97 ZZR1100 '15 Hypermotard 821 SP Do Have: '10 ZX10R
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

stinkwheel
Bovine Proctologist



Joined: 12 Jul 2004
Karma :

PostPosted: 11:03 - 23 Apr 2014    Post subject: Reply with quote

snoosnoo wrote:
Double post, having some weird errors form bcf today!


If you're getting "gateway timeout" errors. Your post will usually have been successfully added to the thread. Try opening the thread in a new tab to check before clicking back and re-posting.

Also. Sticky cam caps usually come up with a cracking noise. Gets my ringpiece going every time!
____________________
“Rule one: Always stick around for one more drink. That's when things happen. That's when you find out everything you want to know.”
I did the 2010 Round Britain Rally on my 350 Bullet. 89 landmarks, 3 months, 9,500 miles.
 Back to top
View user's profile Send private message You must be logged in to rate posts

DrSnoosnoo
World Chat Champion



Joined: 28 Mar 2012
Karma :

PostPosted: 11:43 - 23 Apr 2014    Post subject: Reply with quote

stinkwheel wrote:
snoosnoo wrote:
Double post, having some weird errors form bcf today!


If you're getting "gateway timeout" errors. Your post will usually have been successfully added to the thread. Try opening the thread in a new tab to check before clicking back and re-posting.

Also. Sticky cam caps usually come up with a cracking noise. Gets my ringpiece going every time!


Yeah I pressed Refresh on autopilot which reposted.

Yeah I did hear a cracking the first time and shat it. Once this is out I need to get the cams out and not loose the chain and hopefully not fuck the timing. Is tipex alright to use in oil? or should I just make do with a permanent pen?
____________________
I'm Sam; Northern, Ginger, Lover
Did have: '95 ZZR600 '83 CG125 '97 ZZR1100 '15 Hypermotard 821 SP Do Have: '10 ZX10R
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

mentalboy
World Chat Champion



Joined: 05 May 2012
Karma :

PostPosted: 18:33 - 23 Apr 2014    Post subject: Reply with quote

Take an old wire coat hanger. Open it out and thread it under the chain between the cams so it supports the chain across the length of the head, also stuff some clean rag down the cam chain shaft so that if you drop anything you won't be wondering how to fish it out of the depths!

Take a look at the markings on the cam chain sprockets. Observe how they are lined up - You may need to put a small something in the adjuster hole to take up the slack in the chain. Theoretically there should be a marking on each sprocket that is in line with the cylinder head - if the lower end is still in the correct position. You shouldn't need any marker pens etc Smile
____________________
Make mine a Corona.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

DrSnoosnoo
World Chat Champion



Joined: 28 Mar 2012
Karma :

PostPosted: 20:36 - 23 Apr 2014    Post subject: Reply with quote

So I got the camshafts off by bolting down the other side of the bearing whatsit and then turning each bolt out by half a turn then giving a whack with a rubber mallet and repeated until they were fully turned out. Got the chain hanging on a massive spanner, the cams have the markings on and I took a picture so I'll be prepared to get it back on with the correct timing, I hope.

Found that all the shims were 3mm, so perhaps they're still the stock ones? Ordered 5 replacements from wemoto too so now im waiting.

Wondering whether I should whip the carbs off to check the jets and what have you are at the factory settings, or shall I leave it as it is because it was working fine?
____________________
I'm Sam; Northern, Ginger, Lover
Did have: '95 ZZR600 '83 CG125 '97 ZZR1100 '15 Hypermotard 821 SP Do Have: '10 ZX10R
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

mentalboy
World Chat Champion



Joined: 05 May 2012
Karma :

PostPosted: 20:53 - 23 Apr 2014    Post subject: Reply with quote

Firstly I hope that you weren't describing your hammer action literally!!! Shocked

Have you already ordered the shims? I had the same situation as you fairly recently and discovered purely by chance that it was more economically sound to buy a 'trade' pack of shims (obviously making sure you get the right diameter!!).I think there were about ninety in a box for about £70 which worked out cheaper than the 12 OEM's that I'd been quoted for and gave me a huge amount of options for chopping and changing shims as necessary.
Also gives you somewhere handy to store old shims - don't throw them away as you'll never know when they'll come in handy!
____________________
Make mine a Corona.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

DrSnoosnoo
World Chat Champion



Joined: 28 Mar 2012
Karma :

PostPosted: 07:14 - 24 Apr 2014    Post subject: Reply with quote

mentalboy wrote:
Firstly I hope that you weren't describing your hammer action literally!!! Shocked

Have you already ordered the shims? I had the same situation as you fairly recently and discovered purely by chance that it was more economically sound to buy a 'trade' pack of shims (obviously making sure you get the right diameter!!).I think there were about ninety in a box for about £70 which worked out cheaper than the 12 OEM's that I'd been quoted for and gave me a huge amount of options for chopping and changing shims as necessary.
Also gives you somewhere handy to store old shims - don't throw them away as you'll never know when they'll come in handy!


I was waiting for someone to ask about my hammer action haha! Nah it was a few taps with the hammer between my fingers, really not hard at all.

I've ordered 5 from wemoto for 23 quid, just didn't have the money to buy a big box like you suggest. Probably would next time though! They were 3.58 each so not too costly this time.
____________________
I'm Sam; Northern, Ginger, Lover
Did have: '95 ZZR600 '83 CG125 '97 ZZR1100 '15 Hypermotard 821 SP Do Have: '10 ZX10R
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
Vincent This post is not being displayed because the poster is banned. Unhide this post / all posts.

DrSnoosnoo
World Chat Champion



Joined: 28 Mar 2012
Karma :

PostPosted: 10:16 - 26 Apr 2014    Post subject: Reply with quote

Vincent wrote:
snoosnoo wrote:
Also, looking at these, valves, one side is covered in muck while the other is ok. What are these? The exhaust valves on 1 and 2 are too tight while 3 and 4 are fine.

https://scontent-b-lhr.xx.fbcdn.net/hphotos-frc3/t1.0-9/10308302_10154032987265258_4002090570810439075_n.jpg


They look like pair valves, you're bike Fi? If they are....you don't need em Wink 'Suspicious why one is oilier........worn valve seal maybe?

You're brave if you've never done valve clearances before......my advice would be to check everything three times......and keep your oil ways clean. Wink


Nope it's a carby! Yeah I'm brave but also tight, I don't wanna pay hundreds on this bike that isn't worth much anymore.

The way I see it, if I can get to my final year of a PhD, I can follow some Haynes manuals with the right tools and the internet.
____________________
I'm Sam; Northern, Ginger, Lover
Did have: '95 ZZR600 '83 CG125 '97 ZZR1100 '15 Hypermotard 821 SP Do Have: '10 ZX10R
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 208 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.07 Sec - Server Load: 0.43 - MySQL Queries: 13 - Page Size: 113.02 Kb