|
|
| Author |
Message |
| jetticusblack... |
This post is not being displayed .
|
 jetticusblack... Derestricted Danger
Joined: 25 Apr 2014 Karma :    
|
 Posted: 21:18 - 28 Apr 2014 Post subject: gz 125 marauder brake dragging |
 |
|
Hey guys
recently got myself a half decent budget gz125 and spent today with it in the house checking it over and giving it a shine
found the brake light spring broken so fixed that
throttle felt really loose so tightened it accordingly
gave clutch cable bit of a tighten as it didnt feel great, is a lot better now
back brake is great
new battery and lights are all great but will need to bump for first run to help battery out as pressing starter just makess a single click sound
Stripped damaged stickers off and replaced torn grips
only issue left is my front brake, it is dragging slightly and doesent feel nice, ive been told the pads were replaced recently.
i tried removing the two bolts and pulling the caliper off to look but its refusing to come off the disk!
Help!  |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| davebike |
This post is not being displayed .
|
 davebike World Chat Champion
Joined: 15 Nov 2013 Karma :   
|
 Posted: 07:38 - 29 Apr 2014 Post subject: |
 |
|
Calliper is sized
You will need to leaver the pads apart and the calliper off the disk without bending the disk
It may help to drain the brake fluid
I expect you have to remove the pistons clean the seal groves in the calliper and replace the seals or possible fit new ones
The pistons should clean up with green scourer and WD40 type fluid
Clean the sliding pins
reassemble with red brake grease
Don not use copperslip it will damage the rubber components of brakes
Dave ____________________ Dave
NC750Xdct + others at work !
[email protected] |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| jetticusblack... |
This post is not being displayed .
|
 jetticusblack... Derestricted Danger
Joined: 25 Apr 2014 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| davebike |
This post is not being displayed .
|
 davebike World Chat Champion
Joined: 15 Nov 2013 Karma :   
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| jetticusblack... |
This post is not being displayed .
|
 jetticusblack... Derestricted Danger
Joined: 25 Apr 2014 Karma :    
|
 Posted: 09:43 - 29 Apr 2014 Post subject: |
 |
|
I hope not ive not got many pennies at all was hopeing itd be less of a job than it is, and i can get a new caliper for 50 spose it would be pretty easy to replace considerin its all off already  |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| smegballs |
This post is not being displayed .
|
 smegballs World Chat Champion
Joined: 28 Oct 2007 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| smegballs |
This post is not being displayed .
|
 smegballs World Chat Champion
Joined: 28 Oct 2007 Karma :  
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| jetticusblack... |
This post is not being displayed .
|
 jetticusblack... Derestricted Danger
Joined: 25 Apr 2014 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| davebike |
This post is not being displayed .
|
 davebike World Chat Champion
Joined: 15 Nov 2013 Karma :   
|
 Posted: 07:06 - 30 Apr 2014 Post subject: |
 |
|
Ok
Now you need to bleed the system
The way I used before I had modern kit
Get a long length of clear plastic pipe that fits the bleed screw
Push it on with the open end HIGH and undo the bleed about one turn
Suck on the pipe while working the leaver and watching for fluid in the pipe
As soon as the leaver feel different or fluid appears stop sucking
Keep pumping close the bleed screw if it pumps up hard your done if no re open the bleed and pump some more and try again
DAve ____________________ Dave
NC750Xdct + others at work !
[email protected] |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| jetticusblack... |
This post is not being displayed .
|
 jetticusblack... Derestricted Danger
Joined: 25 Apr 2014 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| jetticusblack... |
This post is not being displayed .
|
 jetticusblack... Derestricted Danger
Joined: 25 Apr 2014 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| jetticusblack... |
This post is not being displayed .
|
 jetticusblack... Derestricted Danger
Joined: 25 Apr 2014 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| jetticusblack... |
This post is not being displayed .
|
 jetticusblack... Derestricted Danger
Joined: 25 Apr 2014 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| jetticusblack... |
This post is not being displayed .
|
 jetticusblack... Derestricted Danger
Joined: 25 Apr 2014 Karma :    
|
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| jetticusblack... |
This post is not being displayed .
|
 jetticusblack... Derestricted Danger
Joined: 25 Apr 2014 Karma :    
|
 Posted: 20:16 - 30 Apr 2014 Post subject: |
 |
|
Fixed! Wahoo! Few hours blowing sucking and massaging pipes *ha*
Found the master cylinder piston/spring was jammed so sorted that out
spent a while blowing fluid into the caliper, then managed to finally get it to take and gravity bled it through
thank you for the advice and help it deffinitely did help  |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| Ariel Badger |
This post is not being displayed .
|
 Ariel Badger Super Spammer

Joined: 02 Dec 2006 Karma :     
|
 Posted: 20:53 - 30 Apr 2014 Post subject: |
 |
|
Sucking you say (repeatedly), I may have a little job for you  ____________________ Bikers make great organ donors, get 115 on your licence today. |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
| jetticusblack... |
This post is not being displayed .
|
 jetticusblack... Derestricted Danger
Joined: 25 Apr 2014 Karma :    
|
 Posted: 00:49 - 01 May 2014 Post subject: |
 |
|
filthy haa  |
|
| Back to top |
|
You must be logged in to rate posts |
|
 |
Old Thread Alert!
The last post was made 12 years, 202 days ago. Instead of replying here, would creating a new thread be more useful? |
 |
|
|