Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


gz 125 marauder brake dragging

Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

jetticusblack...
Derestricted Danger



Joined: 25 Apr 2014
Karma :

PostPosted: 21:18 - 28 Apr 2014    Post subject: gz 125 marauder brake dragging Reply with quote

Hey guys

recently got myself a half decent budget gz125 and spent today with it in the house checking it over and giving it a shine

found the brake light spring broken so fixed that

throttle felt really loose so tightened it accordingly

gave clutch cable bit of a tighten as it didnt feel great, is a lot better now

back brake is great

new battery and lights are all great but will need to bump for first run to help battery out as pressing starter just makess a single click sound

Stripped damaged stickers off and replaced torn grips

only issue left is my front brake, it is dragging slightly and doesent feel nice, ive been told the pads were replaced recently.

i tried removing the two bolts and pulling the caliper off to look but its refusing to come off the disk!

Help! Smile
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

davebike
World Chat Champion



Joined: 15 Nov 2013
Karma :

PostPosted: 07:38 - 29 Apr 2014    Post subject: Reply with quote

Calliper is sized

You will need to leaver the pads apart and the calliper off the disk without bending the disk
It may help to drain the brake fluid

I expect you have to remove the pistons clean the seal groves in the calliper and replace the seals or possible fit new ones

The pistons should clean up with green scourer and WD40 type fluid

Clean the sliding pins

reassemble with red brake grease

Don not use copperslip it will damage the rubber components of brakes


Dave
____________________
Dave
NC750Xdct + others at work !
[email protected]
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

jetticusblack...
Derestricted Danger



Joined: 25 Apr 2014
Karma :

PostPosted: 09:02 - 29 Apr 2014    Post subject: Reply with quote

Ok so ive drained fluid now and disassembled but cant get piston out it wont budge
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

davebike
World Chat Champion



Joined: 15 Nov 2013
Karma :

PostPosted: 09:37 - 29 Apr 2014    Post subject: Reply with quote

You need a specialist tool
A sort of internal collet chuck that fits to a slide hammer

https://www.ebay.co.uk/itm/LASER-TOOLS-3673-MOTORCYCLE-BRAKE-PISTON-REMOVAL-TOOL-/201012446249?pt=UK_Hand_Tools_Equipment&hash=item2ecd468429

You probably now have a job for a workshop Sad(
____________________
Dave
NC750Xdct + others at work !
[email protected]
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

jetticusblack...
Derestricted Danger



Joined: 25 Apr 2014
Karma :

PostPosted: 09:43 - 29 Apr 2014    Post subject: Reply with quote

I hope not ive not got many pennies at all was hopeing itd be less of a job than it is, and i can get a new caliper for 50 spose it would be pretty easy to replace considerin its all off already Sad
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

smegballs
World Chat Champion



Joined: 28 Oct 2007
Karma :

PostPosted: 09:45 - 29 Apr 2014    Post subject: Reply with quote

Fill it with fluid again and pump it without pads in to push the pistons out. If it is a single piston happy days. If not use a pad and a g clamp to incrementally push both pistons out. Eventually they will both be so far our they they can be take out by hand. Compressed air will also get them out, put the pop will make you jump!

For fifty quid you can rebuild the caliper with a new seals and a stainless steel piston, and never worry about it seizing again barring a bit of light cleaning every time you change the pads.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

smegballs
World Chat Champion



Joined: 28 Oct 2007
Karma :

PostPosted: 10:09 - 29 Apr 2014    Post subject: Reply with quote

While a slide hammer is a useful bit of kit to have, I doubt that setup can generate as much force on the pistons and the hydraulic fluid does in normal operation!
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

jetticusblack...
Derestricted Danger



Joined: 25 Apr 2014
Karma :

PostPosted: 20:57 - 29 Apr 2014    Post subject: Reply with quote

Ok so i got someone to rebuild it today and it should be back to its former glory, all lines are completely empty now and it is all refitted but its now not pulling fluid from the reservoir downwards even when i try moving lever etc

i guess this is because theres no fluid in pipes its not working to pull it through but its got me stumped, tried leaving it tried all things i know...
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

davebike
World Chat Champion



Joined: 15 Nov 2013
Karma :

PostPosted: 07:06 - 30 Apr 2014    Post subject: Reply with quote

Ok

Now you need to bleed the system

The way I used before I had modern kit

Get a long length of clear plastic pipe that fits the bleed screw
Push it on with the open end HIGH and undo the bleed about one turn
Suck on the pipe while working the leaver and watching for fluid in the pipe
As soon as the leaver feel different or fluid appears stop sucking

Keep pumping close the bleed screw if it pumps up hard your done if no re open the bleed and pump some more and try again

DAve
____________________
Dave
NC750Xdct + others at work !
[email protected]
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

jetticusblack...
Derestricted Danger



Joined: 25 Apr 2014
Karma :

PostPosted: 09:21 - 30 Apr 2014    Post subject: Reply with quote

Sucking is giving me nothing still, reservoir is full, bleed open and suck and fluid isnt moving down at all
Tried moving lever and nothing doesent to diddley

Ive checked brake lines for blockages of which there are none
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

jetticusblack...
Derestricted Danger



Joined: 25 Apr 2014
Karma :

PostPosted: 09:37 - 30 Apr 2014    Post subject: Reply with quote

Sucking is giving me nothing still, reservoir is full, bleed open and suck and fluid isnt moving down at all
Tried moving lever and nothing doesent to diddley

Ive checked brake lines for blockages of which there are none
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

jetticusblack...
Derestricted Danger



Joined: 25 Apr 2014
Karma :

PostPosted: 09:47 - 30 Apr 2014    Post subject: Reply with quote

Sucking is giving me nothing still, reservoir is full, bleed open and suck and fluid isnt moving down at all
Tried moving lever and nothing doesent to diddley

Ive checked brake lines for blockages of which there are none
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

jetticusblack...
Derestricted Danger



Joined: 25 Apr 2014
Karma :

PostPosted: 10:29 - 30 Apr 2014    Post subject: Reply with quote

Also tried fixing hoover to bleed line and doing same as instructed and still getting no movement..
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

jetticusblack...
Derestricted Danger



Joined: 25 Apr 2014
Karma :

PostPosted: 10:30 - 30 Apr 2014    Post subject: Reply with quote

Also tried fixing hoover to bleed line and doing same as instructed and still getting no movement..
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

jetticusblack...
Derestricted Danger



Joined: 25 Apr 2014
Karma :

PostPosted: 20:16 - 30 Apr 2014    Post subject: Reply with quote

Fixed! Wahoo! Few hours blowing sucking and massaging pipes *ha*

Found the master cylinder piston/spring was jammed so sorted that out

spent a while blowing fluid into the caliper, then managed to finally get it to take and gravity bled it through


thank you for the advice and help it deffinitely did help Smile
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Ariel Badger
Super Spammer



Joined: 02 Dec 2006
Karma :

PostPosted: 20:53 - 30 Apr 2014    Post subject: Reply with quote

Sucking you say (repeatedly), I may have a little job for you Mr. Green
____________________
Bikers make great organ donors, get 115 on your licence today.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

jetticusblack...
Derestricted Danger



Joined: 25 Apr 2014
Karma :

PostPosted: 00:49 - 01 May 2014    Post subject: Reply with quote

filthy haa Razz
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 202 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.05 Sec - Server Load: 0.27 - MySQL Queries: 13 - Page Size: 92.54 Kb