Resend my activation email : Register : Log in 
BCF: Bike Chat Forums


New Tool and now a little nervous

Reply to topic
Bike Chat Forums Index -> The Workshop
View previous topic : View next topic  
Author Message

podmore71
Borekit Bruiser



Joined: 11 Apr 2013
Karma :

PostPosted: 14:56 - 28 Apr 2014    Post subject: New Tool and now a little nervous Reply with quote

I've purchased a Neilsen 1/2" Air Impact Wrench from ebay and I'm afraid to say, it scares the hell out of me before I even use it.

For starters, the instruction manual is not the best i have seen and I am a little confused as to how I go about using it. It comes with an attachment which I believe is the 'oil pot' but I am unsure where this should go or what it is for exactly. Also, the various size sockets don't exactly stay on very snuggly. Certainly nothing like they do on a conventional socket set. Is this normal?

Also, on the side of the gun, there is a location marked 'Oil'. Do i need to put some in before I use it?

Any advice would be much appreciated. I need this to remove my front wheel, so that I can try and sort out my front suspension on my little Honda.

https://i.imgur.com/AOdJVxAl.jpg

https://i.imgur.com/9xtyVSil.jpg
 Back to top
View user's profile Send private message You must be logged in to rate posts

Wafer_Thin_Ham
Super Spammer



Joined: 18 Nov 2005
Karma :

PostPosted: 15:00 - 28 Apr 2014    Post subject: Reply with quote

Why not remove your front wheel with a conventional breaker bar?

I've never used air tools, so can't help, but they're not needed to do any jobs on a motorcycle. Using a breaker bar is a piece of cake.
____________________
My Flickr
 Back to top
View user's profile Send private message You must be logged in to rate posts

covent.gardens
World Clap Champion



Joined: 09 Jun 2012
Karma :

PostPosted: 15:10 - 28 Apr 2014    Post subject: Reply with quote

My air ratchet only lasted 5 minutes and never worked properly... never found out whether it was because I didn't use an inline oil thingy, or it was cheap crap, or the compressor wasn't up to it.

Someone needs to write an idiot's guide to air tools.
 Back to top
View user's profile Send private message You must be logged in to rate posts
Vincent This post is not being displayed because the poster is banned. Unhide this post / all posts.

janner_10
World Chat Champion



Joined: 26 Sep 2011
Karma :

PostPosted: 15:12 - 28 Apr 2014    Post subject: Reply with quote

I wouldn't use one a bike, a decent socket set if by far more useful than.

If its a cheapo Ebay job and especially if the sockets aren't a good fit then check that it is actually metric - if its imperial you may as well throw it away.

In fact, if the sockets don't fit heads well you may as well throw it away.

We lubricate ours at work with a couple of drops of 3 in one every week or so - that's all it needs.

EDIT: Thats drops into the air inlet I should add.
____________________
Yamaha FZS600 (Now gone to heaven) > CBR600F4i (SOLD) > '99 YZF-R1
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

stinkwheel
Bovine Proctologist



Joined: 12 Jul 2004
Karma :

PostPosted: 16:19 - 28 Apr 2014    Post subject: Reply with quote

I would and have used them on a bike but for specific jobs.

Such as uber tight nuts like the stub axle nut on a single sided swingarm and some crank end bolts. Nuts on rotating parts like a clutch centre nut or the bottom bolt on a fork leg.

And on both uber-tight and rotating nuts like front sprocket nuts.

With regard to the impact wrench, yes, impact wrenches don't have a little ball catch to hold the socket on so it simply slides on and off the end.

If it's only for occasional use, I usually just put a few drops of oil down the end of the air inlet before each use.

There is a knob on the bottom that sets the "hit rate" 1 being lowest, 4 being highest. I usually start at 1.

There should be a label on it stating the required working pressure.

So lock the pressure regulator on your compressor to that working pressure, put a few drops of oil down the air inlet of the wrench. Attach the airline (either by screwing it on or by using the quick-release fitting). Select your socket, ensure it is firmly set on the fitting, check the wrench is set to spin the correct way (there is a forward and reverse switch), attach the wrench and pull the trigger.

Should clatter some then undo the fitting. If it doesn't, increase the hit rate and try again. Use your common sense, if it simply isn't moving, check for reasons why and keep an eye on the state of the head of the fitting.

If you're using it for suspension, I presume you're meaning to undo the bottom bolts without the cartridge spinning. You'll need a fairly long, 1/2" drive allen key for that. These aren't impact grade, be warned there is a risk they will shatter when used in an impact wrench so wear eye protection. In reality it doesn't happen, I've done the job many times but you only have one set of eyes.
____________________
“Rule one: Always stick around for one more drink. That's when things happen. That's when you find out everything you want to know.”
I did the 2010 Round Britain Rally on my 350 Bullet. 89 landmarks, 3 months, 9,500 miles.
 Back to top
View user's profile Send private message You must be logged in to rate posts

MarJay
But it's British!



Joined: 15 Sep 2003
Karma :

PostPosted: 17:06 - 28 Apr 2014    Post subject: Reply with quote

The inline oiler goes on the air line between the end of the hose and the connection on the handle of the air wrench. The oil hole has a plug in it on mine which I open and add some 3 in 1 every so often. I don't use an inline oiler as I don't have enough connectors to add it to the system but I just use 3 in 1 as I said.
____________________
British beauty: Triumph Street Triple R; Loony stroker: KR1S; Track fun: GSXR750 L1; Commuter Missile: GSX-S1000F; Cheap project: CBR900RR FireBlade
Remember kids, bikes aren't like lego. You can't easily take a part from one bike and then fit it to another.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

The Artist
Super Spammer



Joined: 06 Jan 2008
Karma :

PostPosted: 17:09 - 28 Apr 2014    Post subject: Reply with quote

ITT: Everyone hating on air tools.

Get some air tool oil is step 1.

Does it have a brand name?
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

gavcarter
Could Be A Chat Bot



Joined: 28 Mar 2009
Karma :

PostPosted: 18:50 - 28 Apr 2014    Post subject: Reply with quote

I use a cheapie one quite often, couple of drops oil in the grub screw before use.

Mine is the opposite to yours the sockets are a bugger to get back off, but mine is fitted with a retainer ring that I assume proper impact sockets have a recess for - but i just use normal sockets on mine.
As long as they are decent brand and 6 sided ive never hit any problems.

Snapped a couple of engine mounting bolts when i "tested" the gun though- was a case of "o0o0o look new toy what can i overtighten" Embarassed Embarassed Embarassed
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

CHR15
Turbo nutter bastard



Joined: 14 Jun 2008
Karma :

PostPosted: 19:21 - 28 Apr 2014    Post subject: Reply with quote

never use it to tighten things up.
____________________
Turbocharged drag thing / project death weapon / GK73A
Ste: I'm not entirely sure how you'd go about verbally abusing someone with a potato but I'm sure it's possible.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

podmore71
Borekit Bruiser



Joined: 11 Apr 2013
Karma :

PostPosted: 08:36 - 29 Apr 2014    Post subject: Reply with quote

Thanks for will the advice guys. Made me feel much better.

I won't be using it that often. I only bought it so I could get the wheels off and at some point, the variator nut.
 Back to top
View user's profile Send private message You must be logged in to rate posts

recman
World Chat Champion



Joined: 26 Mar 2012
Karma :

PostPosted: 09:21 - 29 Apr 2014    Post subject: Reply with quote

Used to use one of those at work but only for speed.
They have their place, I wouldn't bother with it on my bike but then I have arms with a little more girth than a pipe cleaner. Wink
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

........................
Spanner Monkey



Joined: 15 Jan 2014
Karma :

PostPosted: 09:24 - 29 Apr 2014    Post subject: Reply with quote

I've got one, it comes out very rarely but it's good to have one for when you need it. A front sprocket nut being a prime example.
 Back to top
View user's profile Send private message You must be logged in to rate posts

MarJay
But it's British!



Joined: 15 Sep 2003
Karma :

PostPosted: 13:16 - 29 Apr 2014    Post subject: Reply with quote

They are useful, flywheel nut being another example. I gave the flywheel nut on my pitbike a brief brief blast with the windy gun on the lowest setting just to nip it up as otherwise the flywheel turns when you get a socket on it. I'd have never been able to undo it without the windy gun anyway.
____________________
British beauty: Triumph Street Triple R; Loony stroker: KR1S; Track fun: GSXR750 L1; Commuter Missile: GSX-S1000F; Cheap project: CBR900RR FireBlade
Remember kids, bikes aren't like lego. You can't easily take a part from one bike and then fit it to another.
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

stinkwheel
Bovine Proctologist



Joined: 12 Jul 2004
Karma :

PostPosted: 13:44 - 29 Apr 2014    Post subject: Reply with quote

I'd like to know how all these people are getting fork bottom bolts and clutch centre nuts off with their breaker-bars. Or do you keep/fabricate a clutch lockup and holding tool for each bike?

I also use mine to put clutch centre nuts back on again. If theyare not piked anyway, I mark the position it was in with a scribe and rattle it back to the same place.

Also very useful for the gearbox mainshaft on the Enfield which has a nut on either end threaded in opposite directions (so tightening one, undoes the other if you hold both of them).
____________________
“Rule one: Always stick around for one more drink. That's when things happen. That's when you find out everything you want to know.”
I did the 2010 Round Britain Rally on my 350 Bullet. 89 landmarks, 3 months, 9,500 miles.
 Back to top
View user's profile Send private message You must be logged in to rate posts

slowlydoesit
Could Be A Chat Bot



Joined: 14 Oct 2012
Karma :

PostPosted: 13:57 - 29 Apr 2014    Post subject: Reply with quote

stinkwheel wrote:
I also use mine to put clutch centre nuts back on again.

Is it useful/desirable to have an impact driver with controllable torque or are they essentially all or nothing tools? I suspect it doesn't matter when loosening fasteners but when tightening it looks like this kind of wrench could easily overdo it?
____________________
Kawasaki KMX200 with broken fixed powervalves and a stutter
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

stinkwheel
Bovine Proctologist



Joined: 12 Jul 2004
Karma :

PostPosted: 14:40 - 29 Apr 2014    Post subject: Reply with quote

slowlydoesit wrote:

Is it useful/desirable to have an impact driver with controllable torque or are they essentially all or nothing tools? I suspect it doesn't matter when loosening fasteners but when tightening it looks like this kind of wrench could easily overdo it?


Not really all or nothing as such but the longer you squeeze the trigger for, the tighter it will make it. Yes, you could easily overdo it so take care.

I work on the principal that if the fitting has been turned back onto the thread it came off by the same number of turns it was previously, it will be stretched by the same amount. So I put it back in the same position. A lot of cylinder head nuts are done by degrees of turning rather than torque these days.
____________________
“Rule one: Always stick around for one more drink. That's when things happen. That's when you find out everything you want to know.”
I did the 2010 Round Britain Rally on my 350 Bullet. 89 landmarks, 3 months, 9,500 miles.
 Back to top
View user's profile Send private message You must be logged in to rate posts

Shaft
World Chat Champion



Joined: 27 Dec 2010
Karma :

PostPosted: 18:33 - 29 Apr 2014    Post subject: Re: New Tool and now a little nervous Reply with quote

podmore71 wrote:
I need this to remove my front wheel, so that I can try and sort out my front suspension on my little Honda.



If you're having to use an impact gun to remove your front spindle nut, it's either been massively overtorqued or there's a corrosion issue.

Use the gun to crack it off, but put it back on with a torque wrench and clean and lightly coat the spindle thread with copper paste.

As others have said, there are very few bike fixings that need the brute force of impact wrenches, but loads of them can be totally destroyed.

A decent torque wrench is a much more useful tool.
____________________
Things get better with age; I'm close to being magnificent........
20 RE Interceptor, 83 Z1100A3, 83 GS650 Katana
WooHoo, I'm a Man Point Millionaire! https://www.bikechatforums.com/viewtopic.php?t=234035
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

Coxyzxr
Brolly Dolly



Joined: 22 May 2008
Karma :

PostPosted: 18:42 - 29 Apr 2014    Post subject: Reply with quote

stinkwheel wrote:
I'd like to know how all these people are getting fork bottom bolts and clutch centre nuts off with their breaker-bars.


Me too!
____________________
**WAS FITTED "WRONG WAY ROUND" !** CANT ACCOUNT FOR THE STUPID !
 Back to top
View user's profile Send private message You must be logged in to rate posts

merquis00
Nova Slayer



Joined: 21 Apr 2014
Karma :

PostPosted: 21:12 - 29 Apr 2014    Post subject: Reply with quote

Coxyzxr wrote:
stinkwheel wrote:
I'd like to know how all these people are getting fork bottom bolts and clutch centre nuts off with their breaker-bars.


Me too!


https://www.mattwebb.com.au/cbr/socket.jpg
____________________
Current: 2010 WR125X, Carrera crossfire-E.
Project's: '88 GL1500 Trike, Chinese 170cc Monkey
Previous: X9-500, XT125, DNA125, CBF125, YZF-R125, '98 K1200RS, '99 St1100, fantic245
 Back to top
View user's profile Send private message You must be logged in to rate posts
Vincent This post is not being displayed because the poster is banned. Unhide this post / all posts.

stinkwheel
Bovine Proctologist



Joined: 12 Jul 2004
Karma :

PostPosted: 23:27 - 29 Apr 2014    Post subject: Reply with quote

I bought Honda tool part number: 07716-0020100
https://www.davidsilverspares.co.uk/graphics/parts/077160020100.jpg
Having the correct tool rocks.

Jamming the primary gears will only stop the outer basket rotating, not the centre.
____________________
“Rule one: Always stick around for one more drink. That's when things happen. That's when you find out everything you want to know.”
I did the 2010 Round Britain Rally on my 350 Bullet. 89 landmarks, 3 months, 9,500 miles.
 Back to top
View user's profile Send private message You must be logged in to rate posts

Shaft
World Chat Champion



Joined: 27 Dec 2010
Karma :

PostPosted: 00:03 - 30 Apr 2014    Post subject: Reply with quote

stinkwheel wrote:

Having the correct tool rocks.



Indeed it does and, in my extensive experience, an impact gun is not often the right tool.
____________________
Things get better with age; I'm close to being magnificent........
20 RE Interceptor, 83 Z1100A3, 83 GS650 Katana
WooHoo, I'm a Man Point Millionaire! https://www.bikechatforums.com/viewtopic.php?t=234035
 Back to top
View user's profile Send private message Send e-mail You must be logged in to rate posts

stinkwheel
Bovine Proctologist



Joined: 12 Jul 2004
Karma :

PostPosted: 08:09 - 30 Apr 2014    Post subject: Reply with quote

Shaft wrote:

Indeed it does and, in my extensive experience, an impact gun is not often the right tool.


The Honda special tool for removing castellated clutch centre nuts is an impact grade socket.
____________________
“Rule one: Always stick around for one more drink. That's when things happen. That's when you find out everything you want to know.”
I did the 2010 Round Britain Rally on my 350 Bullet. 89 landmarks, 3 months, 9,500 miles.
 Back to top
View user's profile Send private message You must be logged in to rate posts
Old Thread Alert!

The last post was made 12 years, 203 days ago. Instead of replying here, would creating a new thread be more useful?
  Display posts from previous:   
This page may contain affiliate links, which means we may earn a small commission if a visitor clicks through and makes a purchase. By clicking on an affiliate link, you accept that third-party cookies will be set.

Post new topic   Reply to topic    Bike Chat Forums Index -> The Workshop All times are GMT
Page 1 of 1

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Read the Terms of Use! - Powered by phpBB © phpBB Group
 

Debug Mode: ON - Server: biskey (www) - Page Generation Time: 0.07 Sec - Server Load: 0.62 - MySQL Queries: 13 - Page Size: 130.76 Kb